Motorola EP450 - page 59

December 3, 2003 HKLN4215A

6-14 Display Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio — General

2. Position the radio (Figure 6-19), and reconnect the flex connector from the keyboard into the con-

nector located on the bottom of the main board, pushing up the 2 end tabs.

3. Slide the volume potentiometer and frequency switch shafts into their respectiv e holes in th e front

cover. Look through the accessory connector opening to make certain that the wires are not

pinched, between shroud and housing.

4. Push the topside of the board chassis upward until it touches the housing end. Before snapping

the board into the housing, perform the following checks:

a. Open the dust cap and ensure the wires are not pinched between the shroud and housing.

b. Ensure the O-ring is seated in the groove.

c. Ensure that the bottom side of the dust cap is fully pressed into the housing before the

snapping the board into place.

Figure 6-18. Microphone and Speaker Wires Re-assembly

Figure 6-19. Keyboard Flex Cable Connection

Speaker Connector

Microphone

Connector

Shroud

Flex Cable Connector

Radio Chassis

End Tabs

Contents

Main Page Foreword Product Safety and RF Exposure Compliance Computer Software Copyrights Document Copyrights ! Table of Contents Chapter 6 Display Model Disassembly and Re-assembly ................ 6-1 Chapter 7 Non-Display Model Disassembly and Re-assembly ........ 7-1 Chapter 8 Troubleshooting Tables ..................................................... 8-1 List of Figures Page List of Tables Related Publications Chapter 1 Model Charts and Test Specifications 1.1 Radio Model Information 1.2 Model Chart for VHF 146-174 MHz EP450, VHF, 146-174 MHz 1.3 VHF Test Specifications General Transmitter Receiver 1.4 Model Chart for UHF 403-440 MHz EP450, UHF, 403-440 MHz 1.5 Model Chart for UHF 438-470 MHz EP450, UHF, 438-470 MHz 1.6 Model Chart for UHF 465-495 MHz EP450, UHF, 465-495 MHz 1.7 UHF Test Specifications General Transmitter Receiver December 3, 2003 HKLN4215A 1-8 Model Charts and Test Specifications: MIL Standards 1.8 MIL Standards Chapter 2 Theory Of Operation 2.1 Introduction 2.2 Major Assemblies 2.2.1 Receiver 2.2.2 Transmitter Frac N Mod IF IC Chapter 3 Test Equipment, Service Aids, and Service Tools 3.1 Test Equipment 3.2 Service Aids Page December 3, 2003 HKLN4215A 3-4 Test Equipment, Service Aids, and Service Tools: Service Aids Programming/Test Cable Figure 3-1. Programming/Test Cable Figure 3-2. Wiring of the Connectors Chapter 4 Performance Checks 4.1 General 4.2 Power-Up Self Test 4.3 RF Test Mode Page Page 4.0 kHz but 5.0 kHz Page Chapter 5 Radio Alignment Procedures 5.1 Introduction 5.2 CPS Programming Setup 5.3 Radio Tuning Setup 5.3.1 Initial Test Equipment Control Settings 5.4 Transmitter Alignment Options 5.4.1 Reference Oscillator Warp 5.4.2 Modulation Balance Attenuation 5.4.3 Transmit Power Tuning 5.4.3.1 To Perform Transmit High Power Tuning, do the following: 5.4.3.2 To Perform Transmit Low Power Tuning, do the following: - 5.4.4 VCO Attenuation 5.4.4.1 VCO Attenuation 25 kHz 5.4.4.2 VCO Attenuation 12.5 kHz 5.4.4.3 VCO Attenuation 20 kHz 5.4.5 DTMF Deviation Tuning 5.4.6 MDC-1200 Deviation Tuning 5.5 Receiver Tuning 5.5.1 Rated Volume Tuning 5.5.2 Squelch Tuning 5.5.2.1 Manual Squelch Tuning 5.5.2.2 Auto Tune 5.5.3 RSSI System Level Tuning 5.5.4 RSSI Display Tuning 5.6 Utilities 5.6.1 Program Serial No. 5.7 Radio-to-Radio Cloning Page Page Chapter 6 Display Model Disassembly and Re-assembly 6.1 Introduction 6.2 Preventive Maintenance 6.2.1 Inspection 6.2.2 Cleaning Procedures 6.3 Safe Handling of CMOS and LDMOS Devices 6.4 Disassembling and Re-assembling the Radio General 6.4.1 Radio Disassembly Detailed 6.4.1.1 Front Cover From Chassis Disassembly Page Page 6.4.1.2 Dust Cover Disassembly 6.4.1.3 Speaker and Microphone Disassembly 6.4.1.4 Keyboard Removal 6.4.1.5 PTT Disassembly 6.4.1.6 Chassis Disassembly 6.4.2 Radio Re-assembly - Detailed 6.4.2.1 Dust Cover Re-assembly 6.4.2.2 Microphone and Speaker Re-assembly Page 6.4.2.3 Keypad and LCD/Keyboard Re-assembly 6.4.2.4 Keyboard Retainer Re-assembly 6.4.2.5 Chassis Assembly/Re-assembly 6.4.2.6 Chassis and Front Cover Re-assembly Page 6.4.2.7 PTT Re-assembly 6.5 Mechanical View and Parts List 6.5.1 EP450 Display Exploded View and Parts List Figure 6-22. EP450 Display Radio Exploded View 1 Page Chapter 7 Non-Display Model Disassembly and Re-assembly 7.1 Introduction 7.2 Preventive Maintenance 7.2.1 Inspection 7.2.2 Cleaning Procedures 7.3 Safe Handling of CMOS and LDMOS Devices 7.4 Disassembling and Re-assembling the Radio General 7.4.1 Radio Disassembly Detailed 7.4.1.1 Front Cover From Chassis Disassembly Page 7.4.1.2 Dust Cover Disassembly 7.4.1.3 Speaker and Microphone Disassembly 7.4.1.4 PTT Disassembly 7.4.2 Chassis Disassembly 7.4.3 Radio Re-assembly - Detailed 7.4.3.1 Dust Cover Re-assembly 7.4.3.2 Microphone and Speaker Re-assembly 7.4.3.3 Chassis Assembly/Re-assembly 7.4.3.4 Chassis and Front Cover Re-assembly c. 7.4.3.5 PTT Re-assembly Page 7.5 Mechanical View and Parts List 7.5.1 EP450 Non-Display Exploded View and Parts List Figure 7-16. EP450 Non-Display Radio Exploded View Page Chapter 8 Troubleshooting Tables 8.1 Power-Up Error Codes 8.2 Operational Error Codes 8.3 Troubleshooting Table for Receiver 8.4 Troubleshooting Table for Transmitter Page Appendix A Accessories Antennas Carrying Accessories Chargers Batteries Audio Accessories Headsets Remote Speaker Microphones Manuals Page Appendix B Warranty, Service Support, and Replacement Parts 1.1 Scope of Manual 1.2 Warranty 1.2.1 Warranty Period and Return Instructions 1.2.2 After Warranty Period 1.3.2 Motorola Online 1.3.3 Mail Orders 1.3.4 Telephone Orders 1.3.5 Fax Orders 1.3.6 Parts Identification 1.4 Technical Support Page Glossary of Terms