Manuals / Motorola / Portable Media / Portable Radio

Motorola EP450 service manual Keypad and LCD/Keyboard Re-assembly, Keypad Re-assembly

Models: EP450

1 91

Download 91 pages 56.86 Kb

Page 56

Display Model Disassembly and Re-assembly:Disassembling and Re-assembling the Radio — General	6-11

6.4.2.3Keypad and LCD/Keyboard Re-assembly

1.Attach the flex cable from the LCD module to the keyboard, if not already attached (Figure 6-15).

2.Remove protective mylar from window and from keypad, if present.

3.Install the new keypad into the housing. Use the two housing posts for keypad alignment (Figure 6-14).

Full Keypad

Housing Posts

Figure 6-14. Keypad Re-assembly

4.Remove mylar from LCD if present.

CAUTION: Make sure the microphone and speaker wires are not trapped under the LCD module.

!

5.Install the LCD/Keypad sub-assembly into the housing (Figure 6-15).

Flex Cable from LCD Module

Flex Cable to Main PC Board

Figure 6-15. LCD/Keypad Board Re-assembly

HKLN4215A

December 3, 2003

Image 56

Motorola EP450 service manual Keypad and LCD/Keyboard Re-assembly, Keypad Re-assembly

Contents

EP450 HKLN4215A Product Safety and RF Exposure Compliance ForewordComputer Software Copyrights Document CopyrightsTable of Contents Display Model Disassembly and Re-assembly Appendix a Accessories Troubleshooting TablesList of Figures 13. Microphone and Speaker Wires Re-assembly List of Tables Related PublicationsModel Charts and Test Specifications Radio Model InformationModel Chart for VHF 146-174 MHz EP450, VHF, 146-174 MHz Model DescriptionVHF Test Specifications GeneralTransmitter ReceiverModel Chart for UHF 403-440 MHz EP450, UHF, 403-440 MHz Model Chart for UHF 438-470 MHz EP450, UHF, 438-470 MHz Model Chart for UHF 465-495 MHz EP450, UHF, 465-495 MHz UHF Test Specifications LAH65SDH9AA4NMIL Standards MIL-STDMajor Assemblies Theory Of OperationIntroduction If IC Test Equipment Test Equipment, Service Aids, and Service ToolsMotorola Part No Description Characteristics Application Service Aids Motorola Part Description ApplicationTest Equipment, Service Aids, and Service Tools Service Aids Programming/Test Cable 5mmGeneral Power-Up Self TestPerformance Checks RF Test Mode Service Monitor Test Set Power SupplyNo. Description Function Beeps No. of BKCVHF R2 UHF R1 UHF R2 UHF R3 Test Mode Test Name Communications Analyzer Radio Test Set CommentsPerformance Checks RF Test Mode Radio Alignment Procedures CPS Programming SetupRadio Tuning Setup Radio Tuning SetupReference Oscillator Warp Initial Test Equipment Control SettingsTransmitter Alignment Options Modulation Balance Attenuation Under Tx Align menu, select Reference Oscillator Warp FigureTransmit Power Tuning Transmit Power Window High PowerTo Perform Transmit High Power Tuning, do the following To Perform Transmit Low Power Tuning, do the followingVCO Attenuation 25 kHz When using test box RLN4460VCO Attenuation VCO Attenuation 12.5 kHz VCO Attenuation 20 kHzUnder the Tx Align menu, select VCO Attenuation 12.5 kHz Under the Tx Align menu, select VCO Attenuation 20 kHzDtmf Deviation Tuning Under Tx Align, select Dtmf Deviation FigureUnder the Tx Align, select MDC-1200 Signaling Figure Receiver TuningMDC-1200 Deviation Tuning Rated Volume Tuning Perform the rated volume tuning procedure as followsSquelch Tuning Manual Squelch TuningRssi System Level Tuning Auto TuneRssi Display Tuning Under the Rx Align menu, select Rssi Display TuningUtilities Radio-to-Radio CloningProcedure 12. Side Button LocationsRadio Alignment Procedures Radio-to-Radio Cloning Display Model Disassembly and Re-assembly Preventive MaintenanceCleaning Procedures Cleaning External Plastic SurfacesCleaning Internal Circuit Boards and Components Safe Handling of Cmos and Ldmos DevicesDisassembling and Re-assembling the Radio General Radio Disassembly DetailedFront Cover From Chassis Disassembly Antenna and Knob Removal Keyboard Flex Connection Dust Cover Disassembly Speaker and Microphone DisassemblyPTT Disassembly Keyboard RemovalChassis Disassembly Audio jack shroud can be removed from the main boardMicrophone and Speaker Re-assembly Radio Re-assembly DetailedDust Cover Re-assembly 12. Microphone Re-assembly Keypad and LCD/Keyboard Re-assembly 14. Keypad Re-assemblyKeyboard Retainer Re-assembly Chassis Assembly/Re-assemblyChassis and Front Cover Re-assembly 17. Main Board onto Chassis Re-assembly18. Microphone and Speaker Wires Re-assembly PTT Re-assembly 20. Fastening the ChassisMechanical View and Parts List 1 EP450 Display Exploded View and Parts ListMotorola Part Description Number MotorolaDecember 3 Non-Display Model Disassembly and Re-assembly IntroductionSafe Handling of Cmos and Ldmos Devices Disassembling and Re-assembling the Radio General Antenna and Knob Removal Speaker Connector Shroud Microphone Speaker and Microphone Disassembly Chassis Disassembly Removal of Main Board from ChassisDust Cap Re-assembly 11. Speaker Re-assembly 12. Installation of Main Board onto Chassis 13. Microphone and Speaker Wires Re-assembly 15. PTT Re-assembly 1 EP450 Non-Display Exploded View and Parts List 16. EP450 Non-Display Radio Exploded View14Mechanical View and Parts List Troubleshooting Tables Power-Up Error CodesOperational Error Codes Error Code Possible Causes Corrective ActionTroubleshooting Table for Receiver Troubleshooting Table for Transmitter Troubleshooting Tables Troubleshooting Table for Transmitter Appendix a Accessories Carrying AccessoriesAntennas ChargersAudio Accessories HeadsetsRemote Speaker Microphones ManualsAccessories Appendix B Warranty, Service Support, and Replacement Parts WarrantyReplacement Parts Ordering Scope of ManualMotorola Online Mail OrdersTelephone Orders Fax OrdersTechnical Support Motorola de Colombia Service CenterMotorola de Mexico Service Center Appendix B-4 Glossary of Terms Term DefinitionReset