TCP Client Mode | Moxa Technologies 5110 Series specification

NPort 5110 Series User’s Manual

Web Console Configuration

TCP Client Mode

TCP alive check time

Setting	Factory Default	Necessity
0 to 99 min	7 min	Optional

0 min: TCP connection is not closed due to an idle TCP connection.

1 to 99 min: NPort 5110 automatically closes the TCP connection if there is no TCP activity for the given time.

Inactivity time

Setting	Factory Default	Necessity
0 to 65535 ms	0 ms	Optional

0 ms: TCP connection is not closed due to an idle serial line.

0-65535 ms: NPort 5110 automatically closes the TCP connection if there is no serial data activity for the given time.

This parameter defines the maintenance status as Closed or Listen for the TCP connection. The connection is closed if there is no incoming or outgoing data through the serial port during the specific Inactivity time.

If the Inactivity time is set to 0, the current TCP connection is kept active until a connection close request is received. Although Inactivity time is disabled, the NPort 5110 will check the connection status between the NPort 5110 and remote host by sending “keep alive” packets periodically. If the remote host does not respond to the packet, NPort 5110 assumes that the connection was closed down unintentionally. NPort 5110 will then force the existing TCP connection to close.

5-15

Image 37

Moxa Technologies 5110 Series user manual TCP Client Mode, TCP alive check time

Contents

First Edition, December NPort 5110 Series User’s Manual Copyright Notice NPort 5110 User’s ManualTrademarks Disclaimer Table of Contents Ethernet Cables Ethernet Port Pinouts Serial Port Pinouts Introduction Product Features Package ChecklistOverview Product Specifications Getting Started Panel Layout Connecting the Hardware Connecting the Power Connecting the HardwarePanel Layout Connecting to a Serial Device Connecting to the NetworkLED Indicators LED Name LED Color LED Function Initial IP Address Configuration NPort 5110 Administration Suite Factory Default IP AddressDefault IP address Initializing NPort 5110’s IP Address Telnet Console Page Page Serial Console 19200, n, 8 Page Page Choosing the Proper Operation Mode TCP Client Mode TCP Server Mode Real COM Mode UDP ModePair Connection Mode Ethernet Modem Mode Web Console Configuration Opening Your Browser NPort 5110 Series User’s Manual Web Console Configuration Web/Telnet Console Basic SettingsServer name Web Console IP configuration Network SettingsMethod Function Definition Netmask IP addressGateway DNS server 1 / DNS server IP Address Report Snmp SettingsCommunity name Contact Auto report to IP Serial SettingsAuto report to TCP port Auto report period Serial Parameters Real COM Mode Operating SettingsTCP alive check time Max connection Setting Factory Default Necessity To 65535 ms Optional Setting Factory Default Necessity To FF hex None OptionalMax connection 2 to Delimiter Inactivity time TCP Server Mode Setting Factory Default Necessity To FF None Optional Command port Setting Factory Default Necessity 4001 RequiredSetting Factory Default Necessity 966 Optional Local TCP port TCP Client Mode Delimiter Destination IP address 2/3/4 Destination IP addressTCP connect on UDP Mode Local listen port Pair Connection Slave Mode Pair Connection Master Mode Dial-in Ethernet ModemDial-out Disconnection request from local site Disconnection request from remote site AT Commands AT&D Registers TCP port Setting Factory Default Necessity 4001 Required Accessible IP Settings Auto Warning E-mail and Snmp Trap Auto Warning SettingsMail Server Snmp Trap Server Event Type DSR changed DCD changed Load Factory Defaults Change Password Overview Installing Windows Administrator Configuration Configuring Windows Administrator Installing Windows Administrator Page Page Page Configuration Broadcast Search Page Page Unlock Password Protection Unlock LockBlank Fixed Configuring NPort Page Upgrade Firmware Export/Import Monitor Select Add Target Page Page Page Page Port Monitor On-line COM Mapping COM MappingOn-line COM Mapping Off-line COM Mapping Select COM Settings to modify COM No., default setting, etc Page Fast Flush only flush local buffer Page Page Select Apply change Off-line COM Mapping IP Location Page IP Serial LIB Why Use IP Serial Library? What is IP Serial Library?How to install IP Serial Library Example Program IP Serial LIB Function Groups Pinouts and Cable Wiring Ethernet Port Pinouts Serial Port Pinouts Port Pinout DiagramsDB9 Male RS-232 port pinouts for NPort Ethernet Cables Cable Wiring Diagrams Well Known Port Numbers TCP Socket Application Service NPort 5110 Series User’s Manual Well Known Port Numbers UDP Socket Application Service NPort 5110 Series User’s Manual Well Known Port Numbers Snmp Agents with MIB II & RS-232 Like Groups Address Translation MIB System MIB Interfaces MIB TCP MIB Snmp MIB Input Signal Table Output Signal Table Auto IP Report Protocol Info n Auto IP Report FormatID List AP ID & Hardware ID Mapping Table Service Information Following services are provided Moxa Internet Services Moxa Product NPort Serial Number Problem Report Form Moxa NPort Product Return Procedure