+Fcerror | Multi-Tech Systems MT5600DSVD specification

MultiModemDSVD User Guide		4	AT Commands, S-Registers, and Result Codes
Terse	Verbose		Description
185	CONNECT 37333		Connected at 37333 bps (V.90 mode)
185	CARRIER 37333		37333 bps data carrier detected (V.90 mode)
186	CONNECT 38667		Connected at 38667 bps (V.90 mode)
186	CARRIER 38667		38667 bps data carrier detected (V.90 mode)
187	CONNECT 41333		Connected at 41333 bps (V.90)
187	CARRIER 41333		41333 bps data carrier detected (V.90)
188	CONNECT 42667		Connected at 42667 bps (V.90)
188	CARRIER 42667		42667 bps data carrier detected (V.90)
189	CONNECT 45333		Connected at 45333 bps (V.90)
189	CARRIER 45333		45333 bps data carrier detected (V.90)
190	CONNECT 46667		Connected at 46667 bps (V.90)
190	CARRIER 46667		46667 bps data carrier detected (V.90)
191	CONNECT 49333		Connected at 49333 bps (V.90)
191	CARRIER 49333		49333 bps data carrier detected (V.90)
192	CONNECT 50667		Connected at 50667 bps (V.90)
192	CARRIER 50667		50667 bps data carrier detected (V.90)
193	CONNECT 53333		Connected at 53333 bps (V.90)
193	CARRIER 53333		53333 bps data carrier detected (V.90)
194	CONNECT 54667		Connected at 54667 bps (V.90)
194	CARRIER 54667		54667 bps data carrier detected (V.90)
+F4	+FCERROR		V.21 signal received/high speed fax expected
			(V.27, V.29, V.33 or V.17).

47

Image 52

Multi-Tech Systems MT5600DSVD manual +Fcerror

Contents

Page Record of Revisions Introduction AT Commands, S-Registers & Result Codes Appendix E Upgrading the Modem Introduction Introduction FeaturesProduct Description Data What Is in Your Modem Package? Related Manuals Installation Safety Warnings What You Will NeedWe supply You supply Change the Speaker Jumper Mount the FeetOpening the Modem Changing the Speaker Jumper Location of speaker jumper RS232 Connection Connect the Modem to Your SystemLine Connection Power Connection Power-On TestPhone Connection Microphone Connection Installing the Modem Driver Install the Modem DriverRemoving Your Old Modem Driver Install and Configure Your Software Operation Front Panel Configuring the Modem Connecting to the Internet To install and run Dial-Up Networking in Windows 95 or To dial your Internet access providerDial-Up Networking Dial-Up Networking in Windows 95/98 Dial-Up Networking in Windows Me To install Dial-Up NetworkingDial-Up Networking in Windows NT Select Start Settings Network and Dial-up Connections Dial-Up Networking in Windows Fax Operation To Originate a Voice Call in Speakerphone ModeVoice Operation To Originate a Dsvd Call Using the Headset To Answer a Voice Call in Speakerphone ModeTo Answer a Dsvd Call Using the Headset References AT Commands Registers Result Codes AT Commands AT Command Summary Echo Command Mode Characters DS=y Dial Stored Telephone NumberHook Control Information Request Monitor Speaker Volume Monitor Speaker ModeDisplay Legacy Parameters Modulation Handshake Return Online to Data Mode Result Codes Enable/DisablePulse Dialing Select Register Modem Reset Connect Message ControlResult Code Selection Long Space Disconnect Error Correction Modes Data Carrier Detect DCD ControlData Terminal Ready DTR Control Modem-Initiated Flow Control Load Factory Settings 42bis Data Compression22bis Guard Tone Control Telephone Jack Control Communications Mode Asynchronous Communications ModeTest Commands Pulse Dial Make/Break Ratio Display Current Configuration Store Current ConfigurationSelect Profile for Hard Reset Display Last Connection Statistics Line Signal Level Line Signal QualityZy=x Store Telephone Number Data Compression Control PCM Code Selection \An Maximum MNP Block Size\Bn Transmit Break \Kn Break Control \Nn Error Correction Mode Selection \Vn Single Line Connect Message Modulation Selection Subparameters MNP Extended Services Distinctive Ring Control Command #CID=n Caller IDFlash Memory Download Voice Commands Command $SBn Serial Port Baud RateCommand +++ATCR Escape Sequence Command -SMS=nData/DSVD Mode Dsvd Enable/Disable Command #BDR=n Baud Rate SelectCommand #CLS=n Data, Fax, or Voice/Audio Select Command #MDL? Identify Model Register Unit Range Default Description Registers S32 S37 Register Unit Range Default Description S86 Result Codes Terse Verbose Description Protocol ALT +FCERROR Solving Problems None of the Indicators Light Modem Does Not Respond to Commands Light Modem Dials But Cannot Connect Modem4Disconnects While Online File Transfer4Is Slower Than It Should Be Modem4Cannot Connect When AnsweringData Is Being Lost Modem4Doesn’t Work with Caller ID There Are Garbage4 Characters on the MonitorFax and Data4Software Can’t Run at the Same Time Appendixes Appendix a Regulatory Compliance FCC Part 68 Telecom FCC Part Industry Canada Fax Branding Statement Canadian Limitations Notice International Modem Restrictions EMC, Safety, and R&TTE Directive ComplianceNew Zealand Telecom Warning Notice South African Notice Appendix B Technical Specifications MultiModemDSVD User Guide Technical Specifications Voice Compression Test procedure Local Analog Loopback Test V.54 Loop Remote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback test Local Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback test MultiModemDSVD User Guide Loopback Tests Limited Warranty Online Warranty RegistrationService North American Products Technical Support International Products Ordering Accessories Internet Sites Upgrade Overview Identify the Modem Firmware Download the Upgrade File Extract the Upgrade FilesIdentify the Current Firmware Version Clear Your Stored Paramenters Upgrade the Modem’s Firmware Restore Your Parameters Index MultiModemDSVD User Guide Index MultiModemDSVD User Guide Index MultiModemDSVD User Guide Index