Bn Transmit Break | Multi-Tech Systems MT5634ZBA-DID manual

MultiModemDID User Guide		Chapter 4 - AT Commands, S-Registers, Result Codes

Command:	\Bn	Transmit Break
Values:		n = 0–9 in 100 ms units
Default:		3
Description:		In non-error-correction mode only, sends a break signal of the
		specified length to a remote modem. Works in conjunction with
		the \K command.
Command:	\Kn	Break Control
Values:		n = 0–5
Default:		5
Description:		Controls the response of the modem to a break received from
		the computer, the remote modem, or the \B command. The
		response is different for each of three different states.
		Data mode. The modem receives the break from the
		computer:
	\K0	Enters online command mode, no break sent to the remote
		modem.
	\K1	Clears data buffers and send break to the remote modem.
	\K2	Same as \K0.
	\K3	Sends break immediately to the remote modem .
	\K4	Same as \K0.
	\K5	Sends break to the remote modem in sequence with the
		transmitted data.
		Data mode. The modem receives the break from the remote
		modem:
	\K0	Clears data buffers and sends break to the computer.
	\K1	Same as \K0.
	\K2	Sends break immediately to the computer.
	\K3	Same as \K2.
	\K4	Sends break to the computer in sequence with the received data.
	\K5	Same as \K4.
		Online command mode. The modem receives a \Bn
		command from the computer:
	\K0	Clears data buffers and sends break to the remote modem.
	\K1	Same as \K0.
	\K2	Sends break immediately to the remote modem.
	\K3	Same as \K2.
	\K4	Sends break to the remote modem in sequence with the
		transmitted data.
	\K5	Same as \K4.

20

Image 20

$Multi-Tech Systems MT5634ZBA-DID manual Bn Transmit Break, Kn Break Control, Online command mode. The modem receives a \Bn$

Contents

User Guide Record of Revisions Revision Date DescriptionTrademarks Patents Table of Contents MultiModemDID User Guide Contents Introduction FeaturesIntroduction and Description You Supply SafetyWe Supply Connect the Modem to Your System InstallationAssemble the Modem Connect the Modem to the AC Power Outlet Removing Your Old Modem from Windows From Windows 2000, XP Operation Front Panel of the MultiModemDID Modem Did Operation Operation Connecting to the Internet Dial-Up Networking AT Commands, S -Registers Result Codes AT Commands Repeat Last CommandCommunication Standard Setting Answer Echo Command Mode Characters Number ATDT1028806127853500$123456789DS=n Dial Stored Telephone Number Echo Online Data Characters Monitor Speaker Mode Return Online to Data ModeResult Codes Enable/Disable Modulation Handshake Modem Reset Tone DialingResult Code Format Result Code Options Load Factory Settings Asynchronous Communications ModeData Terminal Ready DTR Control XON/XOFF Pacing Control Test Commands Display Current SettingsStore Current Configuration Store Dialing Command \Kn Break Control Online command mode. The modem receives a \Bn\Bn Transmit Break \Nn Error Correction Mode Selection \Tn Inactivity Timer\Qn Flow Control Selection \Vn Protocol Result Code Adaptive Answer Result Code Enable DC n AT Command ControlDirect Connect Enable View Numbers in Blacklist Cisco Configuration Command Speed ResponseCommand +DCS=x,y Select V.44 Data Compression $Dn DTR Dialing Command +DS44=n V.44 Data Compression Data Compression Reporting Enable Synchronous Buffered Mode Modulation Selection Subparameters Mod value Valid max-rate values bps Commands Command +PCW=n Call Waiting EnableModem on Hold Enable PCM Upstream Ignore Command +PMHR=n Modem on Hold Initiate Command +PMHT=n Modem on Hold Timer Other Commands Command +VCID=n Caller ID SelectionCommand +VDR= x, y Distinctive Ring Report Quick Connect Control Command +++ATCR Escape Sequence Command %%%ATCR Remote Configuration Escape Sequence MT5634ZBA-DID Initialization Recommendations Busy-Out Timer at End of Call Wait for Digit Time-Out TimeNumber of did Digits Expected Digit Format Format for Reporting Incoming did Number DF0DF1 DF2Page Register Unit Range Default Description Registers Value Speed Value Rate S42 Value Digital loss Command executed Ring signal detectedCarrier signal lost or not detected Invalid commandPage Setup Remote ConfigurationBasic Procedure Changing the Remote Escape Character Modem Does Not Respond to Commands TroubleshootingNone of the Indicators Light Modem Dials But Cannot Connect Modem Cannot Connect When Answering Modem Disconnects While OnlineModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same Time Did Troubleshooting Appendix a Regulatory Compliance FCC Part 68 Telecom FCC Part Fax Branding StatementCanadian Limitations Notice Industry Canada Appendix B Technical Specifications Fax Upgrade Overview Appendix C Upgrading the Modem’s Firmware Extract the Upgrade Files Appendix D Installing a Modem Under Linux InstallationSelect Dialup Configuration Tool Standard Linux Serial Port Definitions Calling the ISP Select RH PPP Dialer Symbols Index MultiModemDID User Guide Index MultiModemDID User Guide Index