Extension-Entry Callback | Multi-Tech Systems MT5634ZBAV specification

User Guide

callback modem is unable to establish a connection, it tries again, up to the number of attempts specified by the #CBAn command.

6.After the modems reconnect, the following message reappears:

Password>

7.Type the same password that you used to initiate the call. You have three attempts to enter the password or be disconnected.

8.If the password is valid, the following message appears and the modems establish a working connection:

OK Connecting

Extension-Entry Callback

Use this procedure when calling from an extension at the callback num- ber. The password that you use must be set up for an optional exten- sion-entry callback.

1.Using a data communications program such as HyperTerminal, dial the number of the callback modem..

2.When the connection is established, the callback modem responds with the following message:

Password>

3.Type an extension-entry password, press the plus key (+), type the extension to call back to, and press ENTER You have three at- tempts or one minute to enter a valid password.

4.If the password is valid, the following message appears and the modems disconnect:

OK Disconnecting

92

Image 102

Multi-Tech Systems MT5634ZBAV manual Extension-Entry Callback

Contents

Model MT5634ZBA Model MT5634ZBAV Page Model MT5634ZBA Model MT5634ZBAV Models MT5634ZBA and MT5634ZBAV Contents Features User Guide Callback Security Vii Appendix C Loopback Tests Viii 145 User Guide Introduction Page Introduction Product Description Introduction What Is in Your Modem Package? Related Manuals User Guide Quick Start Page Quick Start IntroductionWhat You Will Need We supply Safety Warnings Assemble the Modem Mounting the feet Change the Internal Jumpers Opening the Modem Internal jumpers MT5634ZBAV User Guide Changing the Speaker Jumper Changing the Dial-Up/Leased-Line Jumpers Connect the Modem to Your System Modem connections Phone Connection User Guide RS232 ConnectionLine Connection Microphone Connection MT5634ZBAV only Power Connection Power-On TestQuick Start Speaker Connection MT5634ZBAV only Install the Modem in Windows Adding the Modem to Windows 95 or NT Removing Your Old Modem from Windows 95 or NT Install and Configure Your Software Quick Start User Guide Call the Multi-Tech BBS Windows 95 HyperTerminal Windows Terminal Quick Start Select Start Programs Accessories Fax Compose new fax Send a Fax Other Ways to Access Microsoft Fax Test the MT5634ZBAV Voice Circuits Voice Mail TestLoopback Test Speakerphone Test AT+FCLASS=8 AT+VLS=7 References Features Page Features What Can You Do with Your Modem? Features Data Fax Voice MT5634ZBAV only Required Equipment ComputerSerial Cable Features Telephone Line Communications Software Connecting to the Computer RS232 Connections Features Connecting to the Telephone Line Line Connecting to a Telephone Set PhoneConnecting to a Microphone MIC Connecting to a Speaker Spkr Connecting to a Sound Card SpkrConnecting to Power PWR Surge Protectors and Lightning 56 56K Mode 56,000-32,000 bps. The 56 LED lights whenever Front Panel Features User Guide AT Commands Registers Result Codes Page AT Commands AT Commands, S-Registers, and Result Codes AT Command Summary Enter KeyAnswer Carrier Control Repeat Last CommandCommunication Standard Setting Dial ATDT1028806127853500$123456789 DS=y Dial Stored Telephone Number Hook Control Echo Command Mode CharactersEcho Online Data Characters Information Request Monitor Speaker Volume Monitor Speaker ModeModulation Handshake Pulse Dialing Return Online to Data ModeResult Codes Enable/Disable Set Register Value Result Code Format Sr? Read Register ValueTone Dialing Result Code Options Modem Reset Long Space Disconnect Auto Retrain Data Carrier Detect DCD ControlData Terminal Ready DTR Control 22bis Guard Tone Control Load Factory SettingsCommunications Mode Auxiliary Relay Control Asynchronous Communications Mode Test CommandsData Set Ready DSR Control Display Current Settings Store Current ConfigurationSelect Stored Configuration for Hard Reset \An Select Maximum MNP Block Size Zy=x Store Dialing CommandSpeaker Codec Loopback \Bn Transmit Break \Gn Modem Port Flow Control \Jn Data Buffer ControlBreak Control \Nn Error Correction Mode Selection \Tn Inactivity Timer \Qn Flow Control Selection\Vn Protocol Result Code View Numbers in Blacklist \Xn XON/XOFF Pass-ThroughData Calling Tone Data Compression Control DCn AT Command Control $Dn DTR Dialing$EBn Command #CBF? Callback Failed Attempts Display +ES=n Enable Synchronous Buffered Mode#CBDn Callback Delay #CBAn Callback Attempts Command #CBNy=x Store Callback Password Callback Failed Attempts Reset#CBIn Local Callback Inactivity Timer #CBPn Callback Parity Enter Setup Password Callback Security ResetCallback Enable/Disable Command #S=x Store Setup Password +++ATCR Escape Sequence Register Unit Range Default Description Registers S28 S10S11 S35 Register Unit Range Default Description S36 S37 Register Unit Range Default Description S38 S42S43 S89 Register Unit RangeS48 S108 Result Codes Terse Verbose Description Delayed Remote Configuration Page Basic Procedure Remote Configuration Setup Changing the Setup Password Remote Configuration Changing the Remote Escape Character User Guide Callback Security Page Setup Procedures Callback Security User Guide To Change the Setup Password To Turn Callback Security On and Off To Set the Parity of the Callback Security Messages To Assign Callback Passwords and Phone Numbers Callback Security Calling Procedures Password-Only Callback Number-Entry Callback Extension-Entry Callback Direct Connection Callback Security Commands #CBFR Command #CBPn #CBS0 Zy=+-x,???Store Dialing Command Only after the setup password has been entered 100 Solving Problems Page None of the Indicators Light Solving Problems103 Modem Does Not Respond to Commands 104 105 106 Modem Dials But Cannot Connect 107 108 4The Modem Disconnects While Online 109 File Transfer Is Slower Than It Should Be 110 Data Is Being Lost 111 4The Modem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same Time112 Appendixes Page FCC Regulations for Telephone Line Interconnection Regulatory Compliance115 116 Canadian Limitations Notice 117 FCC Fax Update 118 Compliance with Babt Requirements 119 EMC and Safety Compliance European Low Voltage Directive120 Australian Modem Warning Notice Command DefaultRegister Default 121 Use of Supplied Power Transformer 122 New Zealand Telecom Warning Notice 123 124 Technical Specifications Intelligent Features Error CorrectionMode of Operation Command Buffer AT&T V.32 terbo ITU-T V.32bis/V.32 Carrier Frequencies Carrier FrequenciesITU-T 22bis/V.22 or Fax Carrier ConnectorsBell 103/113 Frequencies Power Requirements DiagnosticsIndicators Power Consumption 130 Loopback Tests 131 Test procedure Local Analog Loopback Test V.54 Loop132 Remote Digital Loopback Test V.54 Loop 133 User Guide Test procedure 134 Local Digital Loopback Test V.54 Loop 135 136 Limited Warranty Warranty, Service, and Technical Support137 Multi-Tech Systems, Inc Woodale Drive Mounds View, MN ServiceTechnical Support Attn Repair Online Warranty Registration Multi-Tech BBS139 If you know the file name If you don’t know the file name140 About the Internet 141 About the Multi-Tech Fax-Back Service About CompuServe142 Upgrade Overview Upgrade Procedures143 Multi-Tech Web Site Identify the Modem FirmwareIdentify the Current Firmware Version 144 Multi-Tech BBS 145 Download the Upgrade File 146 Extract the Upgrade Files Clear Your Stored Paramenters147 Upgrade the Modem’s Firmware 148 Flashwin 149 Restore Your Parameters 150 Index Page Index 153 154 47, 70 155 20, 21 Enable Synchronous Buffered Mode 156 Modem Port Flow Control command 157 158 20, 55 Store Telephone Number command 159 User Guide 160