Multi-Tech Systems MT5634ZBAV guide

User Guide

Changing the Speaker Jumper

The speaker jumper (J8) is next to the external speaker jack (see Figure 2-2).

•To use the MT5634ZBAV modem with a monophonic external speaker, remove the jumper plug from the J8 jumper pins. You can store it by placing it on one jumper pin.

•To use the MT5634ZBAV modem with a stereo speaker or sound card, place the jumper plug on both pins of the J8 jumper. This is the factory default position.

Changing the Dial-Up/Leased-Line Jumpers

As shipped from the factory, your modem is configured for normal dial- up operation. That is, the modem must dial a phone number to connect to another modem. To use the modem on a leased line, you must change jumper J10 to select leased line operation, and J11 to select whether it will be the originating or the answering modem. (If dial-up operation is selected, J11 has no effect.) See Figure 2-2 for jumper locations and positions.

•To use the modem on a leased line, move the J10 jumper plug from the default dial-up position to the leased line position.

•To make the modem the originating modem on the leased line, move the J11 jumper plug to the originate position.

•To make the modem the answering modem on the leased line, leave the J11 jumper plug in the factory default answer position.

14

Image 24

Multi-Tech Systems MT5634ZBAV manual User Guide Changing the Speaker Jumper, Changing the Dial-Up/Leased-Line Jumpers

Contents

Model MT5634ZBA Model MT5634ZBAV Page Model MT5634ZBA Model MT5634ZBAV Models MT5634ZBA and MT5634ZBAV Contents Features User Guide Callback Security Vii Appendix C Loopback Tests Viii 145 User Guide Introduction Page Introduction Product Description Introduction What Is in Your Modem Package? Related Manuals User Guide Quick Start Page Introduction What You Will NeedQuick Start We supply Safety Warnings Assemble the Modem Mounting the feet Change the Internal Jumpers Opening the Modem Internal jumpers MT5634ZBAV User Guide Changing the Speaker Jumper Changing the Dial-Up/Leased-Line Jumpers Connect the Modem to Your System Modem connections User Guide RS232 Connection Line ConnectionPhone Connection Microphone Connection MT5634ZBAV only Power Connection Power-On TestQuick Start Speaker Connection MT5634ZBAV only Install the Modem in Windows Adding the Modem to Windows 95 or NT Removing Your Old Modem from Windows 95 or NT Install and Configure Your Software Quick Start User Guide Call the Multi-Tech BBS Windows 95 HyperTerminal Windows Terminal Quick Start Select Start Programs Accessories Fax Compose new fax Send a Fax Other Ways to Access Microsoft Fax Test the MT5634ZBAV Voice Circuits Voice Mail TestLoopback Test Speakerphone Test AT+FCLASS=8 AT+VLS=7 References Features Page Features What Can You Do with Your Modem? Features Data Fax Voice MT5634ZBAV only Required Equipment ComputerSerial Cable Features Telephone Line Communications Software Connecting to the Computer RS232 Connections Features Connecting to the Telephone Line Line Connecting to a Telephone Set PhoneConnecting to a Microphone MIC Connecting to a Speaker Spkr Connecting to a Sound Card SpkrConnecting to Power PWR Surge Protectors and Lightning 56 56K Mode 56,000-32,000 bps. The 56 LED lights whenever Front Panel Features User Guide AT Commands Registers Result Codes Page AT Commands AT Commands, S-Registers, and Result Codes AT Command Summary Enter KeyAnswer Repeat Last Command Communication Standard SettingCarrier Control Dial ATDT1028806127853500$123456789 DS=y Dial Stored Telephone Number Echo Command Mode Characters Echo Online Data CharactersHook Control Information Request Monitor Speaker Volume Monitor Speaker ModeModulation Handshake Return Online to Data Mode Result Codes Enable/DisablePulse Dialing Set Register Value Sr? Read Register Value Tone DialingResult Code Format Result Code Options Modem Reset Long Space Disconnect Auto Retrain Data Carrier Detect DCD ControlData Terminal Ready DTR Control Load Factory Settings Communications Mode22bis Guard Tone Control Auxiliary Relay Control Asynchronous Communications Mode Test CommandsData Set Ready DSR Control Display Current Settings Store Current ConfigurationSelect Stored Configuration for Hard Reset Zy=x Store Dialing Command Speaker Codec Loopback\An Select Maximum MNP Block Size \Bn Transmit Break \Gn Modem Port Flow Control \Jn Data Buffer ControlBreak Control \Nn Error Correction Mode Selection \Tn Inactivity Timer \Qn Flow Control Selection\Vn Protocol Result Code \Xn XON/XOFF Pass-Through Data Calling ToneView Numbers in Blacklist Data Compression Control DCn AT Command Control $Dn DTR Dialing$EBn +ES=n Enable Synchronous Buffered Mode #CBDn Callback DelayCommand #CBF? Callback Failed Attempts Display #CBAn Callback Attempts Callback Failed Attempts Reset #CBIn Local Callback Inactivity TimerCommand #CBNy=x Store Callback Password #CBPn Callback Parity Callback Security Reset Callback Enable/DisableEnter Setup Password Command #S=x Store Setup Password +++ATCR Escape Sequence Register Unit Range Default Description Registers S10 S11S28 S35 Register Unit Range Default Description S36 S37 Register Unit Range Default Description S38 S42S43 Register Unit Range S48S89 S108 Result Codes Terse Verbose Description Delayed Remote Configuration Page Basic Procedure Remote Configuration Setup Changing the Setup Password Remote Configuration Changing the Remote Escape Character User Guide Callback Security Page Setup Procedures Callback Security User Guide To Change the Setup Password To Turn Callback Security On and Off To Set the Parity of the Callback Security Messages To Assign Callback Passwords and Phone Numbers Callback Security Calling Procedures Password-Only Callback Number-Entry Callback Extension-Entry Callback Direct Connection Callback Security Commands #CBFR Command #CBPn #CBS0 Zy=+-x,???Store Dialing Command Only after the setup password has been entered 100 Solving Problems Page None of the Indicators Light Solving Problems103 Modem Does Not Respond to Commands 104 105 106 Modem Dials But Cannot Connect 107 108 4The Modem Disconnects While Online 109 File Transfer Is Slower Than It Should Be 110 Data Is Being Lost 111 4The Modem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same Time112 Appendixes Page FCC Regulations for Telephone Line Interconnection Regulatory Compliance115 116 Canadian Limitations Notice 117 FCC Fax Update 118 Compliance with Babt Requirements 119 EMC and Safety Compliance European Low Voltage Directive120 Command Default Register DefaultAustralian Modem Warning Notice 121 Use of Supplied Power Transformer 122 New Zealand Telecom Warning Notice 123 124 Technical Specifications Error Correction Mode of OperationIntelligent Features Command Buffer Carrier Frequencies ITU-TAT&T V.32 terbo ITU-T V.32bis/V.32 Carrier Frequencies 22bis/V.22 or Connectors Bell 103/113Fax Carrier Frequencies Diagnostics IndicatorsPower Requirements Power Consumption 130 Loopback Tests 131 Test procedure Local Analog Loopback Test V.54 Loop132 Remote Digital Loopback Test V.54 Loop 133 User Guide Test procedure 134 Local Digital Loopback Test V.54 Loop 135 136 Limited Warranty Warranty, Service, and Technical Support137 Service Technical SupportMulti-Tech Systems, Inc Woodale Drive Mounds View, MN Attn Repair Online Warranty Registration Multi-Tech BBS139 If you know the file name If you don’t know the file name140 About the Internet 141 About the Multi-Tech Fax-Back Service About CompuServe142 Upgrade Overview Upgrade Procedures143 Identify the Modem Firmware Identify the Current Firmware VersionMulti-Tech Web Site 144 Multi-Tech BBS 145 Download the Upgrade File 146 Extract the Upgrade Files Clear Your Stored Paramenters147 Upgrade the Modem’s Firmware 148 Flashwin 149 Restore Your Parameters 150 Index Page Index 153 154 47, 70 155 20, 21 Enable Synchronous Buffered Mode 156 Modem Port Flow Control command 157 158 20, 55 Store Telephone Number command 159 User Guide 160