Manuals / Brands / Computer Equipment / Computer Hardware / Napco Security Technologies / Computer Equipment / Computer Hardware

Napco Security Technologies GEM-DXRP2 28 , ARMED1 , FAULT , READY , WAIT , EXITXX , DISARM XXXSEC

1 36

Download 36 pages, 419.93 Kb

28

KEYPAD MESSAGES

The keypad can display the following functional messages. Many are two-line messages; hold down G to display the second

line. (In this booklet, both are shown simultaneously for convenience). Other diagnostic messages are available for the installer or

servicer. Should any unfamiliar messages appear, call your dealer for service.

All zones operating; system can be armed. If displayed, a number following the “READY”

display denotes the area number. A "MONITOR ON" display indicates that Chime or

Watch Mode is on. Note: If Watch Mode is programmed, “MONITOR ON” will not dis-

play for Chime Mode.

Panel reporting to central station on arming. If necessary, wait for ringback signal before

exiting.

Exit delay in progress. XX denotes exit time remaining. If displayed, BYPASSED indicates

arming with zones bypassed; INSTANT ON indicates arming with Instant protection.

Entry delay in progress. XXX shows entry time remaining.

Panel armed. If displayed, a number following the ARMED display denotes the area num-

ber.

Zone(s) not secured (doors or windows may be open). Faulted zone(s) will scroll.

AC ON

READY

AC ON

WAIT

AC ON

EXITXX

AC ON

FAULT

AC ON

ARMED1

AC ON

DISARM XXXSEC

Contents

Main 2 INTRODUCTION IMPORTANT - TEST YOUR SYSTEM WEEKLY 3 TABLE OF CONTENTS TABLE OF CONTENTS TO SILENCE AN ALARM, ENTER YOUR CODE, AND PRESS J. * Page KEYPAD CONTROLS & INDICATORS 6 ZONES FAULTED 02 BACK DOOR Arming the System 1 2 3 7 CAN'T/ ArmZnF CAN'T/ ArmSil CAN'T/ ArmSnd CAN'T/ ArmRst 8 Area Arming (Optional) Manager's Mode Global Arming TRBL EXX-XX PROTECTING YOURSELF WHILE ON THE PREMISES READY ARMED READY 10 PROTECTING YOURSELF WHILE ON THE PREMISES ARMED Instant Protection 2. instant protection. Page TURNING OF F THE ALAR M (DISARMI NG) WHEN RE TURNING Ambush Day Zone (Day Zone(s) programmed? YES NO) 24-Hour Zone (24-Hour Zone(s) programmed? YES NO) Page Page Page 16 LIMITATIONS OF FIRE ALARM WARNING SYSTEM Page 18 Display Telephone List? (OPTIONAL) (For GEM-P9600/3200 panels only). (Phone Numbers Display System Troubles? (For GEM-P9600/3200 panels only). Displays a 2-digit error code Display Fire Alarms? (For GEM-P9600/3200 panels only). Displays alarms that have oc curred on Display Fire Troubles? (For GEM-P9600/3200 panels only). Displays trouble conditions that 19 Activate Chime? Activate Watch Mode? Reset System Trouble? Start Exit Time? 20 21 Display RF Transmitter Status? Relay Control? CENTRAL STATION MONITORING 23 ADVANCED FEATURES BYPASS WAIT FAULT/ ZONE02 Page Introduction D PROGRAMMING (OPTIONAL) User 01 1. Select the Program Mode as follows: (a) (b) 5. Press J to save the code. 6. Press C to exit the Program Mode. 28 ARMED1 FAULT Zone(s) not secured (doors or windows may be open). Faulted zone(s) will scroll. 29 Arming attempted with zone in trouble. Faulted zones will scroll. Correct trouble to arm. CANCEL CAN'T/ ArmZnf CAN'T/ ArmSil 30 (OPTIONAL) (For partitioned systems only). Code not valid for area. (For Commercial Systems Only). Code not valid for programmed time window. Wrong code entered or "Easy Bypass" function not enabled. AC ON 31 Indicates problem(s) detected on the system (see below). EntNow Check power transformer. Check for blown fuse or circuit breaker; general power outage. Battery weak. If not recharged within 24 hours, replace battery. Page Page Page SYSTEM TROUBLE ERROR CODES NAPCO LIMITED WARRANTY THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.