Napco Security Technologies GEM-DXRP2 D

25

PROGRAMMING (OPTIONAL)

Introduction

The Program Mode (optional) is used to

customize User Codes. Access to the

Program Mode requires a special User

Code, therefore not all users may have

the ability to program.

Notes:

1. If the system contains more than one

keypad, only the keypad designated

“No. 1” may be used for programming

(if in doubt which is No. 1, ask your

installer).

2. Operation of the keypad buttons in

the Program Mode is different from

that for normal operation. Refer to the

accompanying diagram for keypad

functions in the Program Mode.

3. If the selected function requires more

than one screen, scroll the display

using A.

4. While in the Program Mode, the

ARMED and STATUS lights remain

off and burglar and fire alarm func-

tions are disabled.

5. If the keypad detects no activity in the

Program Mode for more than 4 min-

utes, a tone will sound; to silence the

tone, press the blue G button.

6. The programmed code or description

will not be permanently stored until

you press D.

7. To exit the Program Mode, press

C.

Programming User Codes

Do not attempt to program a code contain-

ing any blank spaces between digits. In

selecting your codes, do not program re-

petitive numbers (1111), consecutive

numbers (1234), your birth date, address,

or other obvious combinations. Choose a

code of up to six digits (a minimum of four

is recommended, and required in UL in-

stallations). NOTE: Duplicate Codes are

not allowed; therefore a duplicate Code en-

tered in the LCD Window will erase when

D is pressed.

The User Program Mode is accessed from

the Function Mode as follows:

1. Enter your code, then press A to

enter Function Mode.

2. Answer NO (press F) until

"TurnOn Prog Yes/No" is displayed,

then press the YES button (E).

"User01" will display.

Note: If you pass "TurnOn Prog", press

B to scroll back.

3. Using the number buttons, enter a

User Number as a two-digit number

(enter 1-9 as "01" - "09").

4. Press A. The cursor will advance

to the User Code screen and read the

existing code, if any.

(continued)

Contents

Main 2 INTRODUCTION IMPORTANT - TEST YOUR SYSTEM WEEKLY 3 TABLE OF CONTENTS TABLE OF CONTENTS TO SILENCE AN ALARM, ENTER YOUR CODE, AND PRESS J. * Page KEYPAD CONTROLS & INDICATORS 6 ZONES FAULTED 02 BACK DOOR Arming the System 1 2 3 7 CAN'T/ ArmZnF CAN'T/ ArmSil CAN'T/ ArmSnd CAN'T/ ArmRst 8 Area Arming (Optional) Manager's Mode Global Arming TRBL EXX-XX PROTECTING YOURSELF WHILE ON THE PREMISES READY ARMED READY 10 PROTECTING YOURSELF WHILE ON THE PREMISES ARMED Instant Protection 2. instant protection. Page TURNING OF F THE ALAR M (DISARMI NG) WHEN RE TURNING Ambush Day Zone (Day Zone(s) programmed? YES NO) 24-Hour Zone (24-Hour Zone(s) programmed? YES NO) Page Page Page 16 LIMITATIONS OF FIRE ALARM WARNING SYSTEM Page 18 Display Telephone List? (OPTIONAL) (For GEM-P9600/3200 panels only). (Phone Numbers Display System Troubles? (For GEM-P9600/3200 panels only). Displays a 2-digit error code Display Fire Alarms? (For GEM-P9600/3200 panels only). Displays alarms that have oc curred on Display Fire Troubles? (For GEM-P9600/3200 panels only). Displays trouble conditions that 19 Activate Chime? Activate Watch Mode? Reset System Trouble? Start Exit Time? 20 21 Display RF Transmitter Status? Relay Control? CENTRAL STATION MONITORING 23 ADVANCED FEATURES BYPASS WAIT FAULT/ ZONE02 Page Introduction D PROGRAMMING (OPTIONAL) User 01 1. Select the Program Mode as follows: (a) (b) 5. Press J to save the code. 6. Press C to exit the Program Mode. 28 ARMED1 FAULT Zone(s) not secured (doors or windows may be open). Faulted zone(s) will scroll. 29 Arming attempted with zone in trouble. Faulted zones will scroll. Correct trouble to arm. CANCEL CAN'T/ ArmZnf CAN'T/ ArmSil 30 (OPTIONAL) (For partitioned systems only). Code not valid for area. (For Commercial Systems Only). Code not valid for programmed time window. Wrong code entered or "Easy Bypass" function not enabled. AC ON 31 Indicates problem(s) detected on the system (see below). EntNow Check power transformer. Check for blown fuse or circuit breaker; general power outage. Battery weak. If not recharged within 24 hours, replace battery. Page Page Page SYSTEM TROUBLE ERROR CODES NAPCO LIMITED WARRANTY THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.