Napco Security Technologies GEM-DXRP2 - page 13

13

FIRE PROTECTION

(Applicable only where local ordinance permits use of this alarm control panel for fire protection.)

Fire-Zone Alarm

If a fire is detected, “reset FIRE ALARM” will be displayed and the keypad sounder will

pulse.

1. If a fire is in progress, evacuate the premises immediately! If necessary, call the

Fire Department from an outside phone.

2. Press the C button to silence the keypad sounder.

3. If there is no evidence of a fire, enter your User Code and press J to turn off the

alarm.

4. Check smoke detector(s). If a smoke detector tripped, its red alarm indicator light

will be on.

After the alarm condition is corrected (thermostat cooled down; smoke cleared from

detector; etc.), pressing C again will reset the keypad within about 10 seconds.

Fire-Zone Trouble

1. If a problem in the fire-circuit is detected, “TROUBLE” (fire trouble) will display and

the sounder will pulse to signal a malfunction.

2. Press C to silence the sounder. Call for service immediately!

reset FIRE ALARM

AC ON

FIRE/

ZONEXX

TROUBLE

AC ON

TRBL/

E41-XX

Contents

Main 2 INTRODUCTION IMPORTANT - TEST YOUR SYSTEM WEEKLY 3 TABLE OF CONTENTS TABLE OF CONTENTS TO SILENCE AN ALARM, ENTER YOUR CODE, AND PRESS J. * Page KEYPAD CONTROLS & INDICATORS 6 ZONES FAULTED 02 BACK DOOR Arming the System 1 2 3 7 CAN'T/ ArmZnF CAN'T/ ArmSil CAN'T/ ArmSnd CAN'T/ ArmRst 8 Area Arming (Optional) Manager's Mode Global Arming TRBL EXX-XX PROTECTING YOURSELF WHILE ON THE PREMISES READY ARMED READY 10 PROTECTING YOURSELF WHILE ON THE PREMISES ARMED Instant Protection 2. instant protection. Page TURNING OF F THE ALAR M (DISARMI NG) WHEN RE TURNING Ambush Day Zone (Day Zone(s) programmed? YES NO) 24-Hour Zone (24-Hour Zone(s) programmed? YES NO) Page Page Page 16 LIMITATIONS OF FIRE ALARM WARNING SYSTEM Page 18 Display Telephone List? (OPTIONAL) (For GEM-P9600/3200 panels only). (Phone Numbers Display System Troubles? (For GEM-P9600/3200 panels only). Displays a 2-digit error code Display Fire Alarms? (For GEM-P9600/3200 panels only). Displays alarms that have oc curred on Display Fire Troubles? (For GEM-P9600/3200 panels only). Displays trouble conditions that 19 Activate Chime? Activate Watch Mode? Reset System Trouble? Start Exit Time? 20 21 Display RF Transmitter Status? Relay Control? CENTRAL STATION MONITORING 23 ADVANCED FEATURES BYPASS WAIT FAULT/ ZONE02 Page Introduction D PROGRAMMING (OPTIONAL) User 01 1. Select the Program Mode as follows: (a) (b) 5. Press J to save the code. 6. Press C to exit the Program Mode. 28 ARMED1 FAULT Zone(s) not secured (doors or windows may be open). Faulted zone(s) will scroll. 29 Arming attempted with zone in trouble. Faulted zones will scroll. Correct trouble to arm. CANCEL CAN'T/ ArmZnf CAN'T/ ArmSil 30 (OPTIONAL) (For partitioned systems only). Code not valid for area. (For Commercial Systems Only). Code not valid for programmed time window. Wrong code entered or "Easy Bypass" function not enabled. AC ON 31 Indicates problem(s) detected on the system (see below). EntNow Check power transformer. Check for blown fuse or circuit breaker; general power outage. Battery weak. If not recharged within 24 hours, replace battery. Page Page Page SYSTEM TROUBLE ERROR CODES NAPCO LIMITED WARRANTY THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.