Manuals
/
Brands
/
Computer Equipment
/
Computer Hardware
/
Napco Security Technologies
/
Computer Equipment
/
Computer Hardware
Napco Security Technologies
GEM-DXRP2
30 , DAY ZN , ALARM , FireTb E41-XX , FIRE , ZONEXX , WRONG/ AREA , WRONG/ TIME , WRONG/ CODE CAN'T/ARM/ TROUBLE/AREA #
1
30
36
36
Download
36 pages, 419.93 Kb
30
KEYPAD MESSAGES
(
With pulsing sounder
). Trouble condition on a Day Zone (zone numbers will scroll).
Press
C
to silence sounder.
Note:
Watch Mode must be active.
Alarm Condition, followed by zone number(s). "ALARM" and zones will display after sys-
tem is disarmed. Note zones, then press
C
to clear keypad.
(
With pulsing sounder
). Trouble condition on a FireZone. Press
C
to silence
sounder. Correct trouble or call for service.
(
With pulsing sounder
). Alarm condition on a Fire Zone (zone number(s) will scroll).
Press
C
to silence sounder. Evacuate premises or correct cause of alarm.
(
When Zones Bypassed
("Dsp Bypass")
displayed
) indicates zone(s) that have been de-
activated, where XX represents the zone number(s).
(OPTIONAL) (
For partitioned systems only
). Code not valid for area.
(
For Commercial Systems Only
). Code not valid for programmed time window.
Wrong code entered or "Easy Bypass" function not enabled.
(OPTIONAL) (
In Manager's Mode
). Arming prevented due to unsecured zone. "#" represent s
number of area with unsecured zone. Press area number, then
G
and
D
to switch to
that area with faulted zones(s) displayed. The faulted zone can no w be secured or bypassed,
and
AC ON
DAY ZN
AC ON
ALARM
TROUBLE
AC ON
FireTb
E41-XX
reset FIRE ALARM
AC ON
FIRE
BYPASSED
AC ON
ZONEXX
AC ON
WRONG/
AREA
AC ON
WRONG/
TIME
AC ON
WRONG/
CODE
CAN'T/ARM/
TROUBLE/AREA #
Contents
Main
2
INTRODUCTION
IMPORTANT - TEST YOUR SYSTEM WEEKLY
3
TABLE OF CONTENTS TABLE OF CONTENTS
TO SILENCE AN ALARM, ENTER YOUR CODE, AND PRESS J.
*
Page
KEYPAD CONTROLS & INDICATORS
6
ZONES FAULTED 02 BACK DOOR
Arming the System
1
2
3
7
CAN'T/ ArmZnF
CAN'T/ ArmSil
CAN'T/ ArmSnd
CAN'T/ ArmRst
8
Area Arming (Optional)
Manager's Mode
Global Arming
TRBL EXX-XX
PROTECTING YOURSELF WHILE ON THE PREMISES
READY
ARMED
READY
10
PROTECTING YOURSELF WHILE ON THE PREMISES
ARMED
Instant Protection
2.
instant protection.
Page
TURNING OF F THE ALAR M (DISARMI NG) WHEN RE TURNING
Ambush
Day Zone (Day Zone(s) programmed? YES NO)
24-Hour Zone (24-Hour Zone(s) programmed? YES NO)
Page
Page
Page
16
LIMITATIONS OF FIRE ALARM WARNING SYSTEM
Page
18
Display Telephone List? (OPTIONAL) (For GEM-P9600/3200 panels only). (Phone Numbers
Display System Troubles? (For GEM-P9600/3200 panels only). Displays a 2-digit error code
Display Fire Alarms? (For GEM-P9600/3200 panels only). Displays alarms that have oc curred on
Display Fire Troubles? (For GEM-P9600/3200 panels only). Displays trouble conditions that
19
Activate Chime?
Activate Watch Mode?
Reset System Trouble?
Start Exit Time?
20
21
Display RF Transmitter Status?
Relay Control?
CENTRAL STATION MONITORING
23
ADVANCED FEATURES
BYPASS
WAIT
FAULT/ ZONE02
Page
Introduction
D
PROGRAMMING (OPTIONAL)
User 01
1. Select the Program Mode as follows: (a) (b)
5. Press J to save the code. 6. Press C to exit the Program Mode.
28
ARMED1
FAULT
Zone(s) not secured (doors or windows may be open). Faulted zone(s) will scroll.
29
Arming attempted with zone in trouble. Faulted zones will scroll. Correct trouble to arm.
CANCEL
CAN'T/ ArmZnf
CAN'T/ ArmSil
30
(OPTIONAL) (For partitioned systems only). Code not valid for area.
(For Commercial Systems Only). Code not valid for programmed time window.
Wrong code entered or "Easy Bypass" function not enabled.
AC ON
31
Indicates problem(s) detected on the system (see below).
EntNow
Check power transformer. Check for blown fuse or circuit breaker; general power outage.
Battery weak. If not recharged within 24 hours, replace battery.
Page
Page
Page
SYSTEM TROUBLE ERROR CODES
NAPCO LIMITED WARRANTY
THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.