NEC PX-42XM4A manual Auto ID settings, Image Adjust settings, PLE Link settings, On Delay settings

Information

⬛AUTO ID settings

ON: Enables Auto ID function. In the case shown below, display 1 will be set as ID 1, display 2 as ID2, etc. This can be set only when a 2⋅ 2 or 3⋅ 3 video wall is selected.

MODE2: Turns on the main power of each display more delayed.

* Once this function has been set to “ON”, the POWER

ON/OFF button on the remote control does not function

except for the No.1 monitor.

By pressing the POWER ON button on the remote

control the No.1 monitor will turn on and the others

REMOTE IN

REMOTE OUT

No.1 No.2

No.4 No.3

Display 1

No.1 No.2

No.4 No.3

Display 4

REMOTE

OUT

REMOTE

IN

REMOTE

OUT

REMOTE

IN

No.1 No.2

No.4 No.3

Display 2

No.1 No.2

No.4 No.3

Display 3

REMOTE OUT

REMOTE IN

will be turned on one by one automatically.

* From the second monitor onward, neither the POWER

button on the unit nor the POWER ON button on the

remote control works. However, by pressing and holding

the POWER ON button for more than 3 seconds, the

monitor will be turned on.

PLE LINK

OFF: Disables Auto ID function.

IMAGE ADJUST

The position of the image can be adjusted and flickering of the image can be corrected.

Example: Adjusting the vertical position

On “VIDEO WALL” menu, select “IMAGE ADJUST”, then press the MENU/ENTER button.

The “IMAGE ADJUST” screen appears.

On “V-POSITION” of “IMAGE ADJUST” menu, adjust the position.

	IMAGE ADJUST
ASPECT MODE		:	NORMAL
V- POSITION				: ± 0
H - POSITION				: ± 0
V- HEIGHT				:	0
H - WIDTH				:	0
AUTO PICTURE		:	OFF
FINE PICTURE				:	0
PICTURE ADJ .				:	0
SEL.	ADJ.		EXIT RETURN			V- POSITION	: + 64

Information

⬛IMAGE ADJUST settings

These are the same functions as the IMAGE ADJUST menu on page En-22.

P. ON DELAY (Power on delay)

Use this function to activate power-on delay.

Turn on the AUTO ID before the following operations.

Example: Setting “ON”

Use this function to set a uniform brightness for each display.

Turn on the AUTO ID and set the DIVIDER (at 1, 4 or 9) before the following operations.

Example: Setting “ON”

On “PLE LINK” of “VIDEO WALL” menu, select “ON”, then press the MENU/ENTER button.

VIDEO WALL

DIVIDER		:	1
POSITION
DISP. MODE		:	SPLIT
AUTO ID		:	OFF
IMAGE ADJUST
P. ON DELAY		:	OFF
PLE LINK		:	ON
REPEAT TIMER		:	OFF
SEL.	ADJ.		EXIT RETURN

Information

⬛PLE LINK settings

ON: Sets a uniform brightness for each screen in a video wall. This can be set only when a 2⋅ 2 or 3⋅ 3 video wall is selected.

OFF: Sets the individual screen brightness for each screen in a video wall.

*When this function is set “ON”, connect your plasma

displays with the remote cable (optional) in the order of the position numbers for the 2⋅ 2 video wall. See the

drawing below.

*If there are changes in the DIVIDER or POSITION, the PLE LINK will automatically turn OFF.

On “P. ON DELAY” of “VIDEO WALL” menu, select “ON”.

VIDEO WALL

DIVIDER		:	1
POSITION
DISP. MODE		:	SPLIT
AUTO ID		:	OFF
IMAGE ADJUST
P. ON DELAY		:	ON
PLE LINK		:	OFF
REPEAT TIMER		:	OFF
SEL.	ADJ.		EXIT RETURN

REMOTE IN

REMOTE OUT

No.1 No.2

No.4 No.3

Display 1

No.1 No.2

No.4 No.3

Display 4

REMOTE

OUT

REMOTE IN

REMOTE

OUT

REMOTE IN

No.1 No.2

No.4 No.3

Display 2

No.1 No.2

No.4 No.3

Display 3

REMOTE OUT

REMOTE IN

Information

⬛P. ON DELAY settings

ON: Turns on the main power of each display after a delay time.

OFF: Turns on the main power of all displays at the same time.

(Only for 4⋅ 4 and 5⋅ 5 video wall modes)

MODE1: Turns on the main power of each display delayed.

En-33

*With the 3⋅ 3 video wall, connect the final display to the first display the same way as with 2⋅ 2 video wall.

Note: The remote control can be operated unless the IR REMOTE is set to “OFF”.