Deploy the WG302 Access Point | NETGEAR specification

Reference Manual for the NETGEAR ProSafe Wireless Access Point 802.11g WG302

b.Click the Wireless Settings link in the Setup section of the main menu to view the Wireless Settings menu.

Figure 3-5: Basic Wireless Settings menu

c.Configure the wireless interface for wireless access. See the online help or the Understanding Basic Wireless Settings topic of this Reference Manual for full instructions.

Note: You must set the Regulatory Domain. It may not be legal to operate the wireless access point in a region other than one of those identified in this field.

Now that you have finished the setup steps, you are ready to deploy the WG302 in your network. If needed, you can now reconfigure the computer you used in step 1 back to its original TCP/IP settings.

3DEPLOY THE WG302 ACCESS POINT

a.Disconnect the WG302 and position it where you will deploy it. The best location is elevated, such as wall mounted or on the top of a cubicle, at the center of your wireless coverage area, and within line of sight of all the mobile devices.

b.Lift the antenna on either side so that they are vertical.

Note: Consult the antenna positioning and wireless mode configuration information in the Advanced Configuration chapter of the Reference Manual.

c.Connect an Ethernet cable from your WG302 Access Point to a LAN port on your router, switch, or hub.

3-9	Basic Installation and Configuration

September 2004

Image 32

NETGEAR manual Deploy the WG302 Access Point

Contents

September Technical Support Placement and Range Guidelines Declaration of Conformity Industry Canada Compliance Statement September Contents Chapter Management Appendix a Specifications Contents Chapter About This Manual Audience, Versions, Conventions How to Use this Manual Html version of this manual How to Print this Manual About This Manual Chapter Introduction Key Features Supported Standards and Conventions AutoCell-The Self-Organizing Wireless Network Compatible and Related Netgear Products 802.11g Standards-based Wireless NetworkingAutosensing Ethernet Connections with Auto Uplink System Requirements What’s In the Box? Following table explains the LED indicators Hardware Description LED Description Male DB-9 serial port for serial DTE connections This socket connects to the WG302 12V 1.2A power adapterWG302 provides two detachable antenna Introduction Chapter Basic Installation and Configuration Observing Placement and Range Guidelines Cabling Requirements Default Factory Settings Feature Factory Default Settings Understanding WG302 Wireless Security Options LUHOHVVDWD 6HFXULW\2SWLRQV Installing the WG302 Access Point SET UP the WG302 Access Point Login window Web browser will then display the WG302 settings Login result WG302 home Configure the settings appropriate for your network Basic Settings menu Deploy the WG302 Access Point Verify Wireless Connectivity How to Log In to the WG302 Using Its Default IP Address Understanding Basic Wireless Settings Basic Installation and Configuration Understanding WEP/WPA Security Options Wireless Security Settings Field Description Security Encryption Field Description WPA-PSK Wi-Fi Before You Change the Ssid and WEP Settings Key How to Set Up and Test Basic Wireless Connectivity How to Restrict Wireless Access by MAC Address Select the Turn Access Control On check box Click Apply to save your settings How to Configure WEPTo configure WEP data encryption, follow these steps How to Configure WPA How to Configure WPA-PSK Using the Basic IP Settings Options 10 Wireless Settings menu Access Point Name NetBIOS Select the time zone location for your setting Time Zone Using the Secure Telnet Interface How to Use the CLI via the Console PortThese settings appear below the connector on the back panel Chapter Management CLI Commands Press the return key, and the screen below should appear Using Syslog and Activity Log Information Syslog and Activity Log information Viewing General, Log, Station, and Statistical Information This screen shows the following parameters Statistics Field Description Wireless Access Point Status screen Statistics Fields Upgrading the Wireless Access Point Software Viewing a List of Attached Devices Configuration File Management Saving and Retrieving the Configuration Settings Backup menu Changing the Administrator Password Restoring the WG302 to the Factory Default SettingsUsing the Reset Button to Restore Factory Default Settings Set Password menu Management Chapter Advanced Configuration Understanding Advanced IP Settings for Wireless Clients Understanding Advanced Wireless Settings AutoCell RF Management Configuration AutoCell RF management is enabled by default Additional AutoCell View Management Options Configuring Wireless LAN Parameters Table below describes the advanced wireless parameters Enabling Wireless Bridging and Repeating Advanced Wireless Settings Access Point Mode settings How to Configure a WG302 as a Point-to-Point Bridge Point-to-Point Bridge How to Configure Multi Configure the Operating Mode WG302 AP1 on LAN How to Configure Wireless Repeating Advanced Configuration Chapter Troubleshooting No lights are lit on the access point Wireless LAN activity light does not light up LAN light is not lit Cannot connect to the WG302 to configure it When I enter a URL or IP address I get a timeout error Using the Reset Button to Restore Factory Default Settings Appendix a Specifications Specifications for the WG302 Specifications Appendix B Wireless Networking Basics Wireless Networking OverviewInfrastructure Mode This chapter provides an overview of Wireless networking Network Name Extended Service Set Identification Essid Authentication and WEP Data EncryptionAd Hoc Mode Peer-to-Peer Workgroup Authentication Open System Authentication Shared Key Authentication $XWKHQWLFDWLRQ6WHSV Overview of WEP Parameters Sends Iteback TOO!0 Key Size Wireless Channels WEP Configuration Options WPA Wireless Security How Does WPA Compare to WEP? What are the Key Features of WPA Security? How Does WPA Compare to Ieee 802.11i? Wireless Networking Basics Figure B-3 WPA Overview Access point replies with an EAP-request identity message Figure B-4 802.1x Authentication Sequence WPA Data Encryption Key Management Temporal Key Integrity Protocol Tkip Is WPA Perfect? Product Support for WPA Open system, then 802.1x EAP with Radius or preshared key Open system, then 802.1x supplicant EAP or preshared key Changes to Wireless Client Programs Appendix C Command Line Reference Command Sets Command Line Reference Command Line Reference Command Line Reference Glossary Dhcp DSL Internet service provider Radius TLS Wins Glossary Index Numerics WEP B-3