Industry Canada Compliance Statement | NETGEAR WG302 manual

•Reorient or locate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Warning for North America, and Australia

Warning! To meet FCC and other national safety guidelines for RF exposure, the antennas for this device (see below) must be installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons. Further, the antennas shall not be colocated with other antenna or radio transmitter.

Antenna Statement for North America and Australia

In addition to its own 2 antennas, the WG302 device has been approved for use with the following detachable antennas and antenna cables:

Approved	Antenna Gain and	Approved Antenna	Antenna Cable	Maximum
Antennas	type	Cable	Length	Transmitted Power
NETGEAR	18 dBi, directional	NETGEAR	1.5 m to 30 m	19 dBm + 18 dBi ant.
ANT24D18	outdoor/indoor	ACC-10314-01 thru 05
NETGEAR	9 dBi, omnidirectional	NETGEAR	1.5 m to 30 m	19 dBm + 9 dBi ant.
ANT2409	outdoor/indoor	ACC-10314-01 thru 05
NETGEAR	5 dBi, ceiling/wall	NETGEAR	1.5 m to 30 m	19 dBm + 5 dBi ant.
ANT24O5	indoor	ACC-10314-01 thru 05

* WG302 maximum radiated power in North America and Australia: 20 dBm – cable loss + antenna gain

Please go to www.netgear.com/go/wg302_fcc for an updated list of wireless accessories approved to be used with the WG302 in North America and Australia.

Industry Canada Compliance Statement

This Class B Digital apparatus meets all the requirements of the Canadian Interference Causing Equipment Regulations ICES 003.

Cet appareil numerique de classe B respecte les exigences du reglement du Canada sur le materiel brouilleur NMB-003.

The device is certified to the requirements of RSS-210 for 2.4 GHz spread spectrum devices. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.

5

September 2004

Image 5

NETGEAR WG302 manual Industry Canada Compliance Statement

Contents

September Technical Support Placement and Range Guidelines Declaration of Conformity Industry Canada Compliance Statement September Contents Chapter Management Appendix a Specifications Contents Audience, Versions, Conventions Chapter About This Manual Html version of this manual How to Use this Manual How to Print this Manual About This Manual Chapter Introduction Supported Standards and Conventions Key Features AutoCell-The Self-Organizing Wireless Network Compatible and Related Netgear Products 802.11g Standards-based Wireless NetworkingAutosensing Ethernet Connections with Auto Uplink What’s In the Box? System Requirements Hardware Description Following table explains the LED indicators LED Description Male DB-9 serial port for serial DTE connections This socket connects to the WG302 12V 1.2A power adapterWG302 provides two detachable antenna Introduction Observing Placement and Range Guidelines Chapter Basic Installation and Configuration Cabling Requirements Feature Factory Default Settings Default Factory Settings LUHOHVVDWD 6HFXULW\2SWLRQV Understanding WG302 Wireless Security Options SET UP the WG302 Access Point Installing the WG302 Access Point Login window Login result WG302 home Web browser will then display the WG302 settings Basic Settings menu Configure the settings appropriate for your network Deploy the WG302 Access Point Verify Wireless Connectivity How to Log In to the WG302 Using Its Default IP Address Understanding Basic Wireless Settings Basic Installation and Configuration Understanding WEP/WPA Security Options Wireless Security Settings Field Description Security Encryption Field Description WPA-PSK Wi-Fi Key Before You Change the Ssid and WEP Settings How to Set Up and Test Basic Wireless Connectivity Select the Turn Access Control On check box How to Restrict Wireless Access by MAC Address Click Apply to save your settings How to Configure WEPTo configure WEP data encryption, follow these steps How to Configure WPA-PSK How to Configure WPA 10 Wireless Settings menu Using the Basic IP Settings Options Access Point Name NetBIOS Time Zone Select the time zone location for your setting How to Use the CLI via the Console Port Using the Secure Telnet InterfaceThese settings appear below the connector on the back panel Chapter Management Press the return key, and the screen below should appear CLI Commands Syslog and Activity Log information Using Syslog and Activity Log Information This screen shows the following parameters Viewing General, Log, Station, and Statistical Information Field Description Statistics Wireless Access Point Status screen Statistics Fields Viewing a List of Attached Devices Upgrading the Wireless Access Point Software Configuration File Management Settings Backup menu Saving and Retrieving the Configuration Changing the Administrator Password Restoring the WG302 to the Factory Default SettingsUsing the Reset Button to Restore Factory Default Settings Set Password menu Management Understanding Advanced IP Settings for Wireless Clients Chapter Advanced Configuration AutoCell RF Management Understanding Advanced Wireless Settings AutoCell RF management is enabled by default Configuration Additional AutoCell View Management Options Table below describes the advanced wireless parameters Configuring Wireless LAN Parameters Advanced Wireless Settings Access Point Mode settings Enabling Wireless Bridging and Repeating Point-to-Point Bridge How to Configure a WG302 as a Point-to-Point Bridge Configure the Operating Mode WG302 AP1 on LAN How to Configure Multi How to Configure Wireless Repeating Advanced Configuration No lights are lit on the access point Chapter Troubleshooting LAN light is not lit Wireless LAN activity light does not light up When I enter a URL or IP address I get a timeout error Cannot connect to the WG302 to configure it Using the Reset Button to Restore Factory Default Settings Specifications for the WG302 Appendix a Specifications Specifications Wireless Networking Overview Appendix B Wireless Networking BasicsInfrastructure Mode This chapter provides an overview of Wireless networking Network Name Extended Service Set Identification Essid Authentication and WEP Data EncryptionAd Hoc Mode Peer-to-Peer Workgroup Open System Authentication Authentication $XWKHQWLFDWLRQ6WHSV Shared Key Authentication Sends Iteback TOO!0 Overview of WEP Parameters Key Size WEP Configuration Options Wireless Channels WPA Wireless Security How Does WPA Compare to WEP? How Does WPA Compare to Ieee 802.11i? What are the Key Features of WPA Security? Wireless Networking Basics Figure B-3 WPA Overview Figure B-4 802.1x Authentication Sequence Access point replies with an EAP-request identity message WPA Data Encryption Key Management Temporal Key Integrity Protocol Tkip Product Support for WPA Is WPA Perfect? Open system, then 802.1x supplicant EAP or preshared key Open system, then 802.1x EAP with Radius or preshared key Changes to Wireless Client Programs Command Sets Appendix C Command Line Reference Command Line Reference Command Line Reference Command Line Reference Glossary Dhcp DSL Internet service provider Radius TLS Wins Glossary Numerics Index WEP B-3