4. Cut the plastic tie holding the Upright Wire Harness (98) in | 4 |
| 81 | ||
the right Upright (69). Have a second person hold the |
| ||||
|
| ||||
Handrails (66) near the Uprights as shown. Connect the |
|
|
| ||
Upright Wire Harness (98) to the wire harness extending |
|
| 98 | ||
from the Console Base (81). Insert the connectors and the |
|
|
| ||
Upright Wire Harness into the hole in the right Upright. |
|
|
| ||
Set the Handrails (66) on the Uprights (69), being careful |
|
|
| ||
not to pinch the Upright Wire Harness (98). |
|
| 69 | ||
|
|
|
|
| |
5. Insert two Handrail Bolts (78) with Handrail Washers (77) |
|
| 66 | ||
|
|
| |||
into the right Upright (69) and the right Handrail (66). | Be |
|
| ||
careful not to pinch the wires. | Next, lift the right | 5 |
|
| |
Handrail (66) slightly and align the Bolts with the holes in |
|
| |||
the Handrail. Thread the Bolts into the Handrail. | Do not |
| 69 | ||
tighten the Bolts yet. |
|
|
| ||
|
|
|
| ||
Attach the left Handrail (not shown) in the same way. |
|
|
| ||
Tighten all four Handrail Bolts (78). |
|
|
|
| |
6. Make sure that all parts are properly tightened before |
| 66 | 77 | ||
|
| ||||
|
|
| |||
you use the treadmill. Place a mat beneath the tread- |
|
| 78 | ||
mill to protect the floor. | For your benefit, familiarize |
|
|
| |
yourself with the information on pages 27 and 28. |
|
|
| ||
If you purchase the optional chest pulse sensor (see | 1 |
| C | ||
page 24), follow the steps below to install the receiver |
| ||||
|
| ||||
and the short jumper wire included with the chest pulse |
|
|
| ||
sensor. |
|
|
|
|
|
1. Make sure that the power cord is unplugged. | Remove |
|
| ||
the indicated screws from the Console Back (A). |
|
|
| ||
Important: The screws may be different lengths. Keep |
|
| A | ||
track of which screws were removed from which holes. |
|
| Screws | ||
Remove the Console Back. |
|
|
|
| |
2. Peel the paper off the pad on the bottom of the Receiver | 2 |
|
| ||
|
|
| |||
(B).Turn the Receiver so the cylinder is on the side |
|
|
| ||
shown, | and press the Receiver into the bottom of the |
|
| B | |
Console Base (D) in the indicated location. |
|
| |||
|
|
| |||
|
|
|
|
| Cylinder |
|
|
|
|
| D |
3. Connect the included Short Jumper Wire (E) to the wire on | 3 |
| C | ||
the Receiver (B). Connect the other end of the Short |
| ||||
|
|
| |||
Jumper Wire to the PLS2 jack on the back of the Console |
|
| PLS2 | ||
(C). If there is a wire already plugged into the PLS2 jack, |
|
| |||
|
| Jack | |||
|
|
|
|
| |
unplug it. Note: The other wires included with the receiver may be discarded. The Wire Tie can be used to tie wires, if needed.
Make sure that no wires are pinched. | See step 1. | |
Reattach the Console (C) with the screws. | Important: If | |
the screws are not put back into the same holes from |
| |
which they were removed, the Console will be dam- | E | |
aged. | ||
B |
7
