Manuals / Nortel Networks / Computer Equipment / Modem

Nortel Networks CTA 500dm manual Set Parity, Set Data Bits

Models: CTA 500dm

1 86

Download 86 pages 29.34 Kb

Page 55

Set Parity

AT commands 55

Result Codes

OK Appears when the value is supported.

ERROR Appears when the selected value is not recognized or is not supported.

Set Parity

The Set Parity Command

&P3=value

sets the parity value of the interface between the CTA 500dm and the attached computer. The following table shows the supported values.

Value

0

1

2

Use

none (default)

odd

even

Result Codes

OK Appears when the value is supported.

ERROR Appears when the selected value is not recognized or is not supported.Set Data Bits

Set Data Bits

&P4=value

The Set Data Bits Command sets the number of data bits on the interface between the CTA 500dm and the attached computer. The values 7 and 8 are permitted. The default value is 8 data bits.

Result Codes

OK Appears when the value is supported.

ERROR Appears the selected value is not recognized or is not supported.

P0873832 Issue 05

CTA 500dm On Line Guide

Image 55

Nortel Networks CTA 500dm manual Set Parity, Set Data Bits

Contents

The CTA 500dm in the Digital Network CTA 500dmUsing a CTA 500dm compliant Norstar TAPI Service Provider, the Applications About this document CTA 500dm feature summarySee Installing CTA 500dm and Norstar TAPI Service Provider software First-time setupP0873832 Issue 6 First-time setupCTA 500 dm On Line Guide Installation and setup Wall mounting the CTA 500dm Compact ICS Setting up the ICSModular ICS Setting up the PC Conﬁguration ¥ Installing CTA 500dm and Norstar TAPI Service Provider software¥ ConÞguring the PC serial port Conﬁguring the PC serial port Installing CTA 500dm and Norstar TAPI Service Provider software8. Click OK Conﬁguring the CTA 500dm if not conﬁgured during installation Conﬁgure CTA 500dm to access PP/MP data calls Adding multiple CTA 500dm conﬁgurations Upgrading the CTA 500dm software Uninstalling the CTA 500dm18 Conﬁguration P0873832 IssueCTA 500dm On Line Guide Conﬁgure TAPI dialing properties Installing Norstar TAPI SPInstalling Personal Call Manager Using PCM for the ﬁrst time P0873832 Issue 22 Installing Norstar TAPI SPCTA 500dm On Line Guide Resource sharing ¥ Installing Dial-Up Server ¥ Allowing access to your PC¥ Connecting to a Windows 95 Dial-Up Server ¥ Connecting to Resources on the Dial-Up ServerAllowing access to your PC Installing Dial-Up ServerConnecting to a Windows 95 Dial-Up Server Connecting to Resources on the Dial-Up Server CTA 500dm On Line Guide Note Windows Explorer displays the new drive letter 7. Click OK28 Resource sharing P0873832 IssueCTA 500dm On Line Guide ¥ Serial Interface commands ¥ Serial Interface Control Lines commands AT commands¥ General commands ¥ S-registers commands ¥ Call Control commands ¥ TCM Ports Protocol Selection commandsProﬁle Proﬁle commands summaryLoad Stored Proﬁle on Start-up Load Stored ProﬁleWrite Active Proﬁle to Memory StateState commands summary Enter Download State Return to On-line Data StateGeneral General commands summaryEscape Sequence turn echo on default 36 AT commandsCommand set echo commandRequest Identiﬁcation Set Local Echo View ParametersDisplay Saved Dial String Save Dial StringResult Code Suppression Control Verbose ControlCTA 500dm responsesÓ on page S-registers S-register commands summaryCall Monitoring Result Code Selection Query S-Register Set S-RegisterS-register set Dial Command Call Control commands summaryCall Control Press any key before the call is completed to abort the Dial Command Answer Command Outgoing Call Control Hook CommandOutgoing Call Control commands summary Outgoing Call Bearer Service ControlChannel Speed Control Incoming Call ControlIncoming Voice Bearer Call Rate Incoming Call Control commands summarymessages. See ÒBearer CapabilitiesÓ on page 81 for more information Audio Bearer Call Answer Control Speech Bearer Call Answer ControlRinging Indications Data Bearer Call Answer ControlTCM Ports Protocol Selection TCM Port Protocol Selection CommandRate Adaptation Protocol Selection CTI MUX Mode MP command summaryRate Multiplier Serial Interface Serial Interface commands summarySerial Interface Rate Set Data Bits Set ParitySerial Interface Control Lines Set Stop Bitssets the method of ßow control on the interface between the Serial Interface Control Lines commands summaryFlow Control The Flow Control CommandOK Appears when the value is supported DTR Operation DCD OperationCTS Operation DSR Operation Calling Line IDRI Operation Calling Line ID Query Calling Line ID commands summaryCalling Line ID Delivery Control Result CodesCaller ID Security select CLID security mode Caller ID security commands summaryCaller ID Security Mode Selection Add NumberSee ÒView ParametersÓ on page 38 for more information Delete NumberClear List View ListSummary of AT commands AT commands default 68 AT commandsCommand data bearer serviceAT commands Description 70 AT commandsCommand P0873832 IssuePower problem? TroubleshootingLED problem? ¥ See ÒSet Local EchoÓ on page 38 for more information AT command problem?Data call problem? ¥ Check that you are subscribing to an MP capable service Appendix Canadian & US Safety Installation Instructions Please Read Carefully1. Read and understand all instructions Important Safety Instructions15. Save these instructions CANADIAN AND US REGULATIONSFor Class A Host equipment EMI/EMCFor Class B Host equipment Address for warranty and repairs in the United States WARRANTY INFORMATIONAddress for warranty and repairs in Canada ¥ Point-to-Point Protocol ¥ Multilink PPP Rate adaptation protocol speciﬁcationsBearer Capabilities CTA 500dm LED Initialization strings Numeric CTA 500dm responsesDB-25 connection DB-25 and DB-9 signal summaryAcronyms used in this document LEDÑLight Emitting Diode