Manuals / Brands / Lawn and Garden / Weather Radio / Omega / Lawn and Garden / Weather Radio

Omega ILD24-UTP, ILD44-UTP 3.2.12 Ramp & Soak, Figure 3.11 Flow Chart for Ramp and Soak

1 71

Download 71 pages, 1.13 Mb

46

3.2.12 Ramp & SoakFigure 3.11 Flow Chart for Ramp and Soak

ENTER RAMP AND SOAK MENU:

Press a1) Press a, if necessary, until CNFG prompt appears.

Press d2) Display advances to INPT Input Menu.

Press a3) Press a, if necessary, until Display advances to RAMP Ramp

and SOAK Soak Menu.

RAMP ENABLE/DISABLE SUBMENU:

Press d4) Display advances to “Ramp Enable/Disable” Submenu and

flashes ENBL or DSBL.

Press b5) Scroll through the available selections: “Enable” or “Disable”.

Press d6) Display shows STRD stored message momentarily and then

advances to SOAK Soak Enable/Disable Menu.

If RAMP Disable was selected, display skips to the next menu

item (ID Code).

SOAK ENABLE/DISABLE SUBMENU:

Press d7) Display flashes ENBL or DSBL.

Press b8) Scroll through the available selections: “Enable” or “Disable”.

Press d9) Display shows STRD stored message momentarily and then

advances to “Ramp Value” Submenu.

Alarm must be

DISABLED if Ramp

is ENABLED.

It is recommended that you put the

controller in the Standby Mode for any

configuration change other than

Setpoints & Alarms.

Contents

Main Controller Manual Users Guide ! Servicing North America: For immediate technical or application assistance: Servicing Europe: OMEGAnet On-Line Service www.omega.com TABLE OF CONTENTS LIST OF FIGURES: LIST OF TABLES: NOTES, WARNINGS and CAUTIONS PART 1 INTRODUCTION 1.1 Description 1.2 Safety Considerations EMC Considerations 1.3 Before You Begin Page Page Page 2.3 Electrical Installation 2.3.1 Power Connections + - Figure 2.5 Inside Cover Rear View Figure 2.4 Main Power Connections Page Page Page Page Figure 2.12 Excitation Output Figure 2.13 Snubber Circuits Wiring Hookup PART 3 OPERATION: Configuration Mode 3.1 Introduction Page 3.2.1 ID Number 3.2.2 Set Points Page Input Type (Thermocouple) Input Type (RTD) Input Type (Process) 3.2.5 Reading Configuration Figure 3.4 Flow Chart for Reading Configuration Menu Page Reading Configuration (If Process was selected) Table 3.2 Conversion Table 3.2.6 Alarm 1 Figure 3.5 Flow Chart for Alarm 1 Page Page Page 3.2.7 Analog Output (Retransmission) Figure 3.6 Flow Chart for Analog Output (Retransmission) Page Page 3.2.8 Alarm 2 Figure 3.7 Flow Chart for Alarm 2 3.2.9 Loop Break Time Figure 3.8 Flow Chart for Loop Break Time Page Page Page Page Page Page Page Page Page 3.2.11 Output 2 Figure 3.10 Flow Chart for Output 2 Page Page 3.2.12 Ramp & Soak Figure 3.11 Flow Chart for Ramp and Soak Page 3.2.13 ID CODE Figure 3.12 Flow Chart for ID Code Page Page Page Page Page Page Page 3.2.15 DISPLAY COLOR SELECTION Figure 3.14 Flow Chart for Display Color Selection Page Page PART 4 SPECIFICATIONS Page J K T E R S B C N L RTD Table 4.1 Input Properties PART 5 FACTORY PRESET VALUES Table 5.1 Factory preset value Page CE APPROVAL INFORMATION Page WARRANTY/DISCLAIMER RETURN REQUESTS/INQUIRIES Where Do I Find Everything I Need for Process Measurement and Control? OMEGAOf Course! Shop on line at www.omega.com M3716/0204 TEMPERATURE PRESSURE, STRAIN AND FORCE FLOW/LEVEL