Onkyo HT-R390 Sync, Name, Audio Selector, Setting the Incoming Digital Signal Fixed Mode

Tip

•To fully enjoy Audyssey Dynamic EQ® and Audyssey Dynamic Volume®, we recommend that you manually adjust the level of each speaker using “Level Cal (Level Calibration)” (➔ page 30).

A/V Sync

■A/V Sync

`0 ms to 400 ms in 10 ms steps

When using progressive scanning on your Blu-ray Disc/DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals.

To view the TV picture while setting the delay, press

ENTER.

To return to the previous screen, press RETURN.

The range of values you can adjust will depend on whether your TV or display supports HDMI Lip Sync and if the “LipSync” setting is set to “On” or not

(➔ page 35).

Note

•A/V Sync is disabled when the Direct listening mode is used with an analog input source.

Name

■Name

`- - -,Blu-ray,DVD, HD DVD, VCR, DVR, Tivo, CableSTB, SAT STB, PS3, Wii, Xbox, PC, TV, CD, TAPE, iPod:

To reset to the default, select “- - -”.

You can enter a preset name for each individual input selector for easy identification. When entered, the preset name will appear on the display.

Note

•Can not set the input selector by the same name.

•This menu cannot be used for the TUNER (AM, FM) input selector.

Audio Selector

■Audio Selector

`ARC:

The audio signal from your TV tuner can be sent to the HDMI OUT of the AV receiver.*1

With this selection the TV’s audio can be automatically selected as a priority among other assignments.

`HDMI:

This can be selected when HDMI IN has been assigned as an input source. If both HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) have been assigned, HDMI input is automatically selected as a priority.

`COAXIAL:

This can be selected when COAXIAL IN has been assigned as an input source. If both coaxial and HDMI inputs have been assigned, coaxial input is automatically selected as a priority.

`OPTICAL:

This can be selected when OPTICAL IN has been assigned as an input source. If both optical and HDMI inputs have been assigned, optical input is automatically selected as a priority.

`Analog:

The AV receiver always outputs analog signals. You can set priorities of audio output when there are both digital and analog inputs.

Note

•The setting is stored individually for each input selector.

•This setting can be made only for the input source that is assigned as HDMI IN, COAXIAL IN, or OPTICAL IN. If both HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) are assigned, HDMI input will be selected as a priority by setting to “ARC” (➔ page 35). To select the digital audio input, see “Digital Audio (Digital Audio Input)”

(➔ page 28).

*1 You can select “ARC” if you select the TV/CD input selector. But you cannot select it if you’ve selected “Off” in the “Audio Return Ch” setting (➔ page 35).

Setting the Incoming Digital Signal (Fixed Mode)

■Fixed Mode

`Off:

The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.

`PCM:

Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and noise may also be produced.

`DTS:

Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound.

When “HDMI”, “COAXIAL” or “OPTICAL” is selected in the “Audio Selector” setting, you can then specify the signal type in “Fixed Mode”.

Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS.

•If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM.

•If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS.

Note

•The setting will be reset to “Off” when you change the setting in the “Audio Selector” (➔ page 33).

En

33