Onkyo HT-RC360 Speaker Setup, Component Video Input, Digital Audio Input, Speaker Settings

Component Video Input

If you connect a video component to a component video input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to COMPONENT VIDEO IN 2, you must assign “IN2” to the “BD/DVD” input selector.

Here are the default assignments.

Input selector	Default assignment
BD/DVD	IN1
VCR/DVR	- - - - -
CBL/SAT	IN2
GAME	- - - - -
TV/CD	- - - - -
PORT	- - - - -

■BD/DVD, VCR/DVR, CBL/SAT, GAME, TV/CD,

PORT

`IN1, IN2:

Select a corresponding component video input to which the video component has been connected.

`- - - - -:

Select if you are using the HDMI output, not the component video output, to output composite video and component video sources.

Note

•If you connect a component (such as UP-A1 Dock with docked iPod/iPhone) to the UNIVERSAL PORT jack, you cannot assign any input to the “PORT” selector.

•The “AUX” selector is fixed at the “- - - - -” option.

•The “TUNER” selector cannot be assigned and is fixed at the “- - - - -” option.

Digital Audio Input

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign “OPTICAL1” to the “TV/CD” input selector.

Here are the default assignments.

Input selector	Default assignment
BD/DVD	COAXIAL1
VCR/DVR	- - - - -
CBL/SAT	COAXIAL2
GAME	OPTICAL1
TV/CD	OPTICAL2
PORT	- - - - -

En

■BD/DVD, VCR/DVR, CBL/SAT, GAME, TV/CD,

PORT

`COAXIAL1, COAXIAL2, OPTICAL1, OPTICAL2:

Select a corresponding digital audio input to which the component has been connected.

`- - - - -:

Select if the component is connected to an analog audio input.

Note

•When an HDMI IN is assigned to an input selector in “HDMI Input” (➔ page 41), the same HDMI IN will be set as a priority in this assignment. In this case, if you want to use the coaxial or optical audio input, make the selection in the “Audio Selector” (➔ page 50).

•Available sampling rates for PCM signals from a digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

•If you connect a component (such as UP-A1 Dock with docked iPod/iPhone) to the UNIVERSAL PORT jack, you cannot assign any input to the “PORT” selector.

•The “AUX” selector is fixed at the “- - - - -” option.

•The “TUNER” selector cannot be assigned and is fixed at the “- - - - -” option.

Speaker Setup

Main menu Speaker Setup

Some of the settings in this section are set automatically by Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 29).

Here you can check the settings made by Audyssey 2EQ Room Correction and Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using Audyssey 2EQ Room Correction and Speaker Setup function.

Note

•These settings are not available in either of the following cases:

–a pair of headphones is connected.

–the “Audio TV Out” setting is set to “On” (➔ page 53).

–“HDMI Control (RIHD)” is set to “On” (➔ page 52) and you’re listening through your TV speakers.

Speaker Settings

If you change these settings, you must run Audyssey 2EQ Room Correction and Speaker Setup again (➔ page 29).

If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms. If you bi-amp the front speakers, you must change the “Speakers Type (Front)” setting (➔ page 43). For hookup information, see “Bi-amping the Front Speakers” (➔ page 14).

Note

•When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers in the main room.

•Before you change these settings, turn down the volume.

42