Using the [USER] button
You can assign one of eleven functions to the [USER] button. Using the [USER] button allows you to easily switch the portable recorder function.
1 Select [USER] from the [OTHER FUNCTIONS] setup menu. Using the setup menus (Page 29)
2 Select the function∗ that you want to assign
to the [USER] button, and then press the [ENTER] button.
∗The functions that can be assigned are shown in the table below.
3 Press the [MENU] button to close the menu.
4 Press the [USER] button.
The function that you assigned to the [USER] button operates.
|
| Press the [SHIFT/EXEC] | ||
|
| button during REC mode | ||
|
| to display the assigned | ||
| USER ASSIGN:COUNTER | function on the LCD | ||
| monitor screen. |
| ||
|
|
|
| |
|
|
|
| |
| Screen display | Usable modes | ||
| SDI |
| CAM | |
|
|
| ||
| INT | ○ |
| ○ |
| REC CHECK | |
| ○ |
|
|
| ||
|
|
|
|
|
| SPOTLIGHT | |
| ○ |
|
|
| ||
|
|
|
|
|
| BACKLIGHT | |
| ○ |
|
|
| ||
|
|
|
|
|
| ATW LOCK | |
| ○ |
|
|
| ||
|
|
|
|
|
| LCD DTL | ○ |
| ○ |
|
|
|
| |
|
|
|
|
|
| LCD REVERSE | ○ |
| ○ |
|
|
|
| |
|
|
|
|
|
| INDEX | ○ |
| ○ |
|
|
|
| |
|
|
|
|
|
| SHOT MARK∗1 | ○ |
| ○ |
|
|
|
| |
|
|
|
|
|
| LAST CLIP | ○ |
| ○ |
|
|
|
| |
|
|
|
|
|
| COUNTER∗2 | ○ |
| ○ |
|
|
|
| |
|
|
|
|
|
∗1 If [SHOT MARK] is assigned to the [USER] button, it can be used during the thumbnail display.
∗2 If [COUNTER] is assigned to the [USER] button, it can be used during clip playback.
•[COUNTER] is assigned as the factory default.
•If you press the [USER] button to operate a function and then turn off the power, the function is canceled. (However, [LCD DTL] is not canceled.)
■INH (Disable operation)
When INH is assigned, there is no operation when the [USER] button is pressed.
■REC CHECK (Check the recording) When the [USER] button is pressed during shooting standby, about 2 seconds of the video and audio that were recorded immediately before are played back. After playback, the portable recorder returns to shooting standby.
•Only the [POWER] button, [REC/PAUSE] button and [AUDIO MON/ADV] buttons are operable during REC CHECK.
•The REC CHECK images are also recorded when a device is connected to the portable recorder and backup images are being recorded.
•The [USER] button will not work even if it is pressed when any of the following operations have been performed upon completion of recording/shooting.
•Operation is switched to the PB mode
•Recording format is changed
•Portable recorder’s power is turned off and then turned back on
•SD Memory Card is ejected
■SPOTLIGHT
Performs auto iris control for the spotlight. “SPOT” is displayed on the screen. Press the [USER] button again to cancel. When [MANUAL] is selected from the setup
menu [CAMERA SETUP] → [IRIS], even pressing the [USER] button will not cause this to operate.
■BACKLIGHT (Backlight compensation) When the shooting subject is lit from behind, performs backlight compensation auto iris control so that the subject does not come out dark. “BACK” is displayed on the screen.
Press the [USER] button again to cancel the backlight compensation.
When [MANUAL] is selected from the setup menu [CAMERA SETUP] → [IRIS], even pressing the [USER] button will not cause this to operate.
■ATW LOCK
Fixes the white balance value when the [USER] button is pressed during ATW.
“LOCK” is displayed on the screen.
Press the [USER] button again to perform the ATW function.
(Continued on the next page)
Recording
41