4. Specifications

DVI-D input/output

Digital RGB:

 

 

 

 

 

 

XGA (1024768), WXGA (1280768), SXGA (12801024), WSXGA+ (16801050),

 

UXGA (16001200), WUXGA (19201200)

 

 

 

 

Vertical frequency: 60 Hz

 

 

 

 

 

Video format inputs:

 

 

 

 

 

 

Digital RGB: 1080/50p, 1080/59.94p

 

 

 

 

 

Vertical frequency: Same as system formats

 

 

 

 

Video format outputs:

 

 

 

 

 

 

Digital RGB: 1080/50p, 1080/59.94p, 1080/50i, 1080/59.94i, 720/50p, 720/59.94p

 

pp The input and output of analog signals are not supported.

 

 

 

 

pp Output support the high-resolution multi view mode:

 

 

 

 

Signals are output with a high resolution even when SD is set as the system mode.

 

(When high-resolution multi view mode has been enabled, MV is selected as the DVI-D OUT

 

output, and it is not possible to select MV with SDI OUT.)

 

 

 

 

pp This connector does not support the HDCP technologies.

 

 

 

 

Standard input/output: 1 line each (DVI-D IN, DVI-D OUT)

 

 

 

 

pp The DVI-I connector cable cannot be used.

 

 

 

 

pp For the DVI-D connector cable, use a cable with a length of up to 5 m (16.4 ft).

 

Reference input/output

In gen-lock mode:

Black burst or Tri-level Sync input signals (with loop-through)

 

In internal sync mode: Black burst output signals 2

 

 

 

 

pp Same field frequencies as those of the system formats supported.

 

 

 

 

pp With the 1080/23.98PsF and 1080/24PsF formats, only gen-lock mode supported.

 

pp With the 1080/23.98PsF format, black burst with 10F-ID (SMPTE318M standard met) or TRI

 

signals supported.

 

 

 

 

 

Video delay time

When the frame synchronizer setting is “Off” and the up-converter setting is

 

1 line (H)

 

“Off”.

 

 

 

 

 

 

When the frame synchronizer setting is “On” or the up-converter setting is “On”.

1 frame (F)

 

pp When the signals have passed through PinP, DVE, multi view, down-converter, DVI-IN or

 

DVI-OUT, a maximum delay of 1 frame is applied in each case.

 

 

 

Control I/O

LAN

10BASE-T/100BASE-TX (For IP control)

RJ-45

 

 

 

Connecting cable:

 

 

 

 

 

 

LAN cable (category 5 or above),

 

 

 

 

 

max. 100 m (328 ft), STP (Shielded Twisted

 

 

 

 

 

Pair) cable recommended

 

 

 

 

 

pp When connecting to a hub (switching hub),

 

 

 

 

 

use a straight cable.

 

 

 

 

 

Use a crossover cable when connecting the

 

 

 

 

 

unit and computer on a 1:1 basis without

 

 

 

 

 

going through a hub.

 

 

 

 

 

pp Use with the same segment is recommended

 

 

 

 

 

for the equipment which is connected to the

 

 

 

 

 

unit.

 

 

 

 

 

 

If the unit is connected to equipment whose

 

 

 

 

 

segments are different, events dependent

 

 

 

 

 

upon the settings inherent to the network

 

 

 

 

 

equipment, for instance, may occur so

 

 

 

 

 

thoroughly check the connections with the

 

 

 

 

 

equipment to which the unit will be connected

 

 

 

 

 

prior to the start of operation.

 

 

 

 

EDITOR

Used to control an editor

D-sub, 9-pin, female

 

 

RS-422 control connector

 

 

 

 

 

Communication format

 

 

 

 

 

Baud rate

: 38400 bps

 

 

 

 

 

Character length: 8 bit

 

 

 

 

 

Parity

: Odd

 

 

 

 

 

Stop bit

: 1 bit

 

 

 

 

 

Flow control

: None

 

 

 

36