Panasonic BTT273, SC-BTT770 Messages, Radio, Wireless system SH-FX71, On the television, Network

Radio

Distorted sound or noise is heard.

≥Adjust the position of the antenna.

≥ Use an outdoor antenna. ( 16)

A beat sound is heard.

≥Try to keep a certain amount of distance between the antenna and the TV.

[BTT770]

Wireless system (SH-FX71)

No power.

≥Ensure the AC power supply cord of the wireless system is connected properly.

The wireless link indicator is flashing.

≥There is no link between the main unit and the wireless system. Turn the wireless system off and then back on. Alternatively, turn the wireless system off, disconnect the AC power supply cord and then reconnect it.

The wireless link indicator does not light.

≥Check that the main unit is turned on, and the wireless system is turned on.

≥Ensure that the digital transmitter is fully inserted into the slot

of the main unit. ( 17)

The wireless link indicator keeps flashing between red and green.

≥There is a power supply problem. Consult the dealer.

Messages

The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use.

On the television

Cannot play.

≥You inserted an incompatible disc. (Discs recorded in PAL video, etc.)

Cannot display on this unit.

≥You tried to play a non-compatible image.

No disc is inserted.

≥The disc may be upside down.

$This operation is not available.

≥Some operations are unsupported by the unit. For example; jBD-Video: During playback, reverse slow-motion or

reverse frame-by-frame is not possible.

IP address is not set.

≥The “IP Address” in “IP Address / DNS Settings” is “---. ---.

---. ---”. Set the “IP Address”, “Subnet Mask”, and “Default Gateway”. (Select the automatic address acquisition if necessary.)

No Video

≥Depending on the connected iPod/iPhone, video menu may not be available on the TV. Select “ALL” on the unit’s display and operate video playback from your iPod/iPhone menu.

( 34)

Network

On the unit’s display

I can’t connect to the network.

≥ Confirm the network connection and settings. ( 17, 20, 40)

≥Check the operating instructions for each device and connect accordingly.

Other difficulties with playback

BD-Video or DVD-Video is not played.

≥Ensure the disc is for the correct BD-Video region code or

DVD-Video region number, and is not defective. ( 8)

≥You have set a ratings level to limit BD-Video or DVD-Video

play. Change this setting. ( 37)

≥Some BD-Video can only be output with HDMI.

I cannot play back BD-Live.

≥ The SD card is write-protected. ( 9)

≥Confirm that this unit is connected to the broadband Internet.

( 17)

≥ Confirm the “BD-Live Internet Access” settings. ( 37)

≥ Confirm an SD Card is inserted into the SD Card slot. ( 22)

Alternative soundtrack and subtitles cannot be selected.

≥The languages are not recorded on the disc.

≥You may not be able to use the playback menu to change the soundtrack and subtitles on some discs. Use the disc’s

menus to make changes. ( 25)

F99

≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to standby for 3 seconds. Now press [POWER Í/I] on the main unit again to turn the unit on.

U59

≥The unit is hot.

The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears.

Select a position with good ventilation when installing the unit. Do not block the ventilation hole on the rear and side of the unit.

HDMI ONLY

≥Some BD-Video discs can only be output with HDMI.

NET

≥While connecting to a network.

Reference

Angle cannot be changed.
≥ Angles can only be changed during scenes where different	VQT3D27
angles are recorded.	45