External Output Control | Panasonic KX-HCM230 specs

Operating Instructions

3.5.10 External Output Control

External Output Control window enables the External Device Control Output signal to activate the external sensors/devices. (Open or Short to GND) The network administrator should set up this setting.

Note

Refer to page 101 for Interfacing to the External I/O.

1.Click [External Output Control] on Setup Page.

2.Check [Open] means the External Device Control Output becomes high impedance (open collector).

Check [Short to GND] means the External Device Control Output becomes low (0V).

3.Click [Save] to send the signal.

•Click [Cancel] to quit the current settings. The window returns to Setup Page without saving the parameters.

[For assistance, please call: 1-800-272-7033]

83

Image 83

Panasonic KX-HCM230 operating instructions Click External Output Control on Setup

Contents

Network Camera For operation assistance Call Introduction For assistance, please call TrademarksNetwork Camera Memo Important Safety Instructions Table of Contents Index 125 Specifications and Troubleshooting 106Technical Guides Section Getting to Know Network Camera Main Features External I/O Input/Output Multi Client AccessUpdate Firmware Authentication System Requirements Authentication window Authentication-System Security Feature AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Included AccessoriesSetup CD-ROM 1 pc Rubber Cap 1 pc Self Bonding tape Connector Cover Setup CD-ROM Fixed Focus Lens Camera Feature LocationsLens Cover Indicator Front View Bottom View Rear View Network Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeNetwork Camera can be installed on the LAN/Intranet Network Camera can be connected to a PC directly Type 3-Internet Direct Connection with a ModemType 4-Direct Connection with a PC How to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera Type Port No Network Camera Configuration TypeDefault Network Parameters Table Click OK to close IP Configuration window How to refer the network parameters from the PC Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Port Forwarding IP Masquerade feature Network Camera Access from the Internet If Top Page does not appear Top Operating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Help Motion JpegSingle Camera Multi-Camera ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Click Delete Deleting the preset buttons Viewing Buffered Image Screen Non Transfer mode Alarm/Timer mode Secondary ViewerClicking Start Capture Primary Multi-Camera Screen Setup Setup Name/Time AdministratorCamera Setup Go to Top Functions of Network Camera Try this option first. Refer to Go to Top Network Enter only the number Instructions for the data fields Or administrator for the Host name If you use Network Camera on the LAN, set upCheck Dhcp Dynamic Host Configuration Protocol Host Name When your ISP uses the Dhcp server function which File size of the image Date Name/TimeCamera Name Time Zone AdjustmentTime Changed AM/PM or 24H Auto Click Security Administrator on Setup Security AdministratorRefer to page 61 for details about authentication security Retype EnableAdministrator and General User Authentication window For Setup Password Security General User Click Security General User on Setup Operating Instructions Top View Image 160 x ResolutionInstructions for the data fields Top Image Image Transfer Non Transfer mode Click Alarm on the Image Transfer window Transfer in the Alarm Mode Active Time of Trigger Alarm enable condition Login timing Data transfer method Over write setting Setting Example Setting explanation Transfer in the Timer Mode Image Frequency Sets the interval to send the image Buffers or transfers by the timer trigger Login timing Over write setting Fixed Camera SetupInstructions for the data fields White Balance Fixed Indoor Tilt Range White Balance is also registered in preset programmingSuggested Having reached the selected end Specifying the Pan/Tilt range Click Save when finished Multi-Camera Camera Name Enable check boxIP Address or URL * 1 or Host External Output Control Click External Output Control on Setup Indicator Control Status Click Restart Now Click Cancel to quit. The window returns to the SetupRestart Update Firmware Click Update Firmware Click Update Firmware on Setup Open Reset to Factory Default Technical Guides Network Camera Installation DC Plug Network Camera Cabling Attach the Sunshade by fastening the two screws Be sure to thread the AC adaptor cord through the hook Inches Cover the putties by rolling Tripod Mounting Network Camera MountingFlexible Stand Mounting Wall Mounting Ceiling Mounting Top Bottom Making holes on mortar wall External Sensor Input Interfacing to the External I/OExplanation of External I/O Pin Function Circuit Diagram Example For assistance, please call 103 Ascii and ISO-8859-1 Character TableUnavailable character set Space, , , #, &, %, =, +, ?, , and are not available 104 Displayable character set For assistance, please call 105 MaintenanceLens Cover 106 Specifications and Troubleshooting For assistance, please call 107 Network Camera Reset Procedure-Default Settings 108 Default Settings List For assistance, please call 109 Alarm 110 Items Factory Default Indispensable setting Value Alarm For assistance, please call 111 Items Factory Default Indispensable setting Value Timer Items Factory Default Indispensable setting Value Camera For assistance, please call 113 Preset Buttons Other Specification Description SpecificationsNetwork Camera Specifications Description Quality and the object situation Message Transferring MethodMm 3.46 inches Situation in Buffered Image Problem Cause and Remedy TroubleshootingAbout Network Camera Setup If Top Page does not appear in the above procedure, press Proxy server may prevent you from connecting directly toWhen Top Page does not appear, port number 80 might not be When you use DDNS, you need to set Default Gateway Transfers older For Indicator Control windowNetwork window on Update About Network Camera Setup Problem Cause and Remedy Lens About Top View Image screen About Other Troubles View Image Setting window on Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information 125 Index Operating Instructions TCP/IP When you ship the product For product service