Manuals / Panasonic / Photography / Security Camera

Panasonic KX-HCM230 Network Camera Mounting, Flexible Stand Mounting, Tripod Mounting

Models: KX-HCM230

1 128

Download 128 pages 56.99 Kb

Page 96

Operating Instructions

4.1.2Network Camera Mounting

Four mounting methods are shown in the following figures. Confirm the top and bottom of Network Camera when mounting. Ask the authorized dealer for mounting.

Note

Mounting and cabling instructions described in this Operating Instructions follow generally accepted guidelines suitable for residential installations. In some areas, commercial and industrial installations are regulated by local or state ordinances. For such installations, contact your local building department or building inspector for more details.

Flexible Stand Mounting

1)Attach Network Camera by screwing the threaded mount into the tripod mounting hole.

2)Turn the grip to fix the Flexible Stand firmly.

1)

Tripod 2) mounting

hole

Tripod Mounting

Attach Network Camera to the tripod using the tripod bolt.

Tripod mounting hole

96

Image 96

Panasonic KX-HCM230 operating instructions Network Camera Mounting, Flexible Stand Mounting, Tripod Mounting

Contents

Network Camera Introduction For operation assistance CallTrademarks Network Camera MemoFor assistance, please call Important Safety Instructions Table of Contents Specifications and Troubleshooting 106 Technical GuidesIndex 125 Section Main Features Getting to Know Network CameraMulti Client Access Update FirmwareAuthentication External I/O Input/OutputSystem Requirements Authentication-System Security Feature Authentication windowIncluded Accessories Setup CD-ROM 1 pc Rubber Cap 1 pcSelf Bonding tape Connector Cover AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pcSetup CD-ROM Camera Feature Locations Lens Cover IndicatorFront View Fixed Focus LensRear View Bottom ViewNetwork Camera Setup Installation Procedure Network Camera Configuration Type Network Camera can be installed on the LAN/IntranetType 2-Internet Connection with a Broadband Router Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PCNetwork Camera can be connected to a PC directly How to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Network Camera Configuration Type DefaultNetwork Parameters Table Type Port NoHow to refer the network parameters from the PC Click OK to close IP Configuration windowSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Network Camera Access from the Internet Port Forwarding IP Masquerade featureTop If Top Page does not appearOperating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Motion Jpeg Single CameraMulti-Camera HelpActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Deleting the preset buttons Click DeleteNon Transfer mode Alarm/Timer mode Viewing Buffered Image ScreenViewer Clicking Start CapturePrimary SecondaryMulti-Camera Screen Setup Setup Administrator Camera SetupGo to Top Name/TimeTry this option first. Refer to Functions of Network CameraGo to Top Network Instructions for the data fields Enter only the numberIf you use Network Camera on the LAN, set up Check Dhcp Dynamic Host Configuration ProtocolHost Name When your ISP uses the Dhcp server function which Or administrator for the Host nameFile size of the image Name/Time CameraName DateAdjustment Time Changed AM/PM or 24HAuto Time ZoneSecurity Administrator Refer to page 61 for details about authentication securityClick Security Administrator on Setup Enable Administrator and General User Authentication windowFor Setup Password RetypeClick Security General User on Setup Security General UserOperating Instructions Top View Image Resolution Instructions for the data fields TopImage 160 xImage Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on the Image Transfer windowAlarm enable condition Active Time of TriggerLogin timing Over write setting Data transfer methodSetting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Image Frequency Sets the interval to send the imageLogin timing Over write setting Camera Setup Instructions for the data fields White BalanceFixed Indoor FixedWhite Balance is also registered in preset programming SuggestedHaving reached the selected end Tilt RangeClick Save when finished Specifying the Pan/Tilt rangeMulti-Camera Enable check box IP Address orURL * 1 or Host Camera NameClick External Output Control on Setup External Output ControlIndicator Control Status Click Cancel to quit. The window returns to the Setup RestartClick Restart Now Update Firmware Click Update Firmware on Setup Click Update FirmwareOpen Reset to Factory Default Technical Guides Network Camera Installation Network Camera Cabling DC PlugBe sure to thread the AC adaptor cord through the hook Attach the Sunshade by fastening the two screwsCover the putties by rolling InchesNetwork Camera Mounting Flexible Stand MountingTripod Mounting Wall Mounting Ceiling Mounting Top Bottom Making holes on mortar wall Interfacing to the External I/O Explanation of External I/OPin Function External Sensor InputCircuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setSpace, , , #, &, %, =, +, ?, , and are not available For assistance, please call 103Displayable character set 104Maintenance Lens CoverFor assistance, please call 105 Specifications and Troubleshooting 106Network Camera Reset Procedure-Default Settings For assistance, please call 107Default Settings List 108Alarm For assistance, please call 109Items Factory Default Indispensable setting Value Alarm 110Items Factory Default Indispensable setting Value Timer For assistance, please call 111Items Factory Default Indispensable setting Value Camera Preset Buttons For assistance, please call 113Specifications Network Camera Specifications DescriptionOther Specification Description Message Transferring Method Mm 3.46 inchesSituation in Buffered Image Quality and the object situationTroubleshooting About Network Camera SetupProblem Cause and Remedy Proxy server may prevent you from connecting directly to When Top Page does not appear, port number 80 might not beWhen you use DDNS, you need to set Default Gateway If Top Page does not appear in the above procedure, pressFor Indicator Control window Network window onTransfers older About Network Camera Setup Problem Cause and Remedy UpdateAbout Top View Image screen LensView Image Setting window on About Other TroublesConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information Index 125Operating Instructions TCP/IP For product service When you ship the product