Wall Mounting | Panasonic KX-HCM230 specification

Operating Instructions

Wall Mounting

1)Mount the Flexible Stand firmly to a wall or beam using the three screws (accessories). Set the Flexible Stand 165 mm (6.5 inches) away from the ceiling.

•Use appropriate screws suited for the material of the wall.

2)Attach Network Camera by screwing the threaded mount into the tripod mounting hole. A mounting hole on the rear side is also available.

3)Adjust the position of Network Camera and secure the Flexible Stand firmly.

4)Roll up the cables and Flexible Stand with the Self Bonding tape (accessories). Refer to page 92 for waterproofing the cables.

1)	2)

165 mm

(6.5 inches)

Caulk around Flexible

Stand if necessary.

3)4)

Waterproof the rest of the cable.

Self Bonding tape

[For assistance, please call: 1-800-272-7033]

97

Image 97

Panasonic KX-HCM230 operating instructions Wall Mounting

Contents

Network Camera For operation assistance Call Introduction Network Camera Memo TrademarksFor assistance, please call Important Safety Instructions Table of Contents Technical Guides Specifications and Troubleshooting 106Index 125 Section Getting to Know Network Camera Main Features Update Firmware Multi Client AccessAuthentication External I/O Input/Output System Requirements Authentication window Authentication-System Security Feature Setup CD-ROM 1 pc Rubber Cap 1 pc Included AccessoriesSelf Bonding tape Connector Cover AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Setup CD-ROM Lens Cover Indicator Camera Feature LocationsFront View Fixed Focus Lens Bottom View Rear View Network Camera Setup Installation Procedure Network Camera can be installed on the LAN/Intranet Network Camera Configuration TypeType 2-Internet Connection with a Broadband Router Type 4-Direct Connection with a PC Type 3-Internet Direct Connection with a ModemNetwork Camera can be connected to a PC directly How to turn on Network Camera for Installation Preparing the Network Parameters for Network Camera Network ParametersNetwork parameters memo for Network Camera Default Network Camera Configuration TypeNetwork Parameters Table Type Port No Click OK to close IP Configuration window How to refer the network parameters from the PC Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Port Forwarding IP Masquerade feature Network Camera Access from the Internet If Top Page does not appear Top Operating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Example TopHttp//Global IP address of Broadband RouterPortNo Top Single Camera Motion JpegMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Click Delete Deleting the preset buttons Viewing Buffered Image Screen Non Transfer mode Alarm/Timer mode Clicking Start Capture ViewerPrimary Secondary Multi-Camera Screen Setup Setup Camera Setup AdministratorGo to Top Name/Time Functions of Network Camera Try this option first. Refer to Go to Top Network Enter only the number Instructions for the data fields Check Dhcp Dynamic Host Configuration Protocol If you use Network Camera on the LAN, set upHost Name When your ISP uses the Dhcp server function which Or administrator for the Host name File size of the image Camera Name/TimeName Date Time Changed AM/PM or 24H AdjustmentAuto Time Zone Refer to page 61 for details about authentication security Security AdministratorClick Security Administrator on Setup Administrator and General User Authentication window EnableFor Setup Password Retype Security General User Click Security General User on Setup Operating Instructions Top View Image Instructions for the data fields Top ResolutionImage 160 x Image Transfer Non Transfer mode Click Alarm on the Image Transfer window Transfer in the Alarm Mode Active Time of Trigger Alarm enable condition Login timing Data transfer method Over write setting Setting Example Setting explanation Transfer in the Timer Mode Image Frequency Sets the interval to send the image Buffers or transfers by the timer trigger Login timing Over write setting Instructions for the data fields White Balance Camera SetupFixed Indoor Fixed Suggested White Balance is also registered in preset programmingHaving reached the selected end Tilt Range Specifying the Pan/Tilt range Click Save when finished Multi-Camera IP Address or Enable check boxURL * 1 or Host Camera Name External Output Control Click External Output Control on Setup Indicator Control Status Restart Click Cancel to quit. The window returns to the SetupClick Restart Now Update Firmware Click Update Firmware Click Update Firmware on Setup Open Reset to Factory Default Technical Guides Network Camera Installation DC Plug Network Camera Cabling Attach the Sunshade by fastening the two screws Be sure to thread the AC adaptor cord through the hook Inches Cover the putties by rolling Flexible Stand Mounting Network Camera MountingTripod Mounting Wall Mounting Ceiling Mounting Top Bottom Making holes on mortar wall Explanation of External I/O Interfacing to the External I/OPin Function External Sensor Input Circuit Diagram Example Unavailable character set Ascii and ISO-8859-1 Character TableSpace, , , #, &, %, =, +, ?, , and are not available For assistance, please call 103 104 Displayable character set Lens Cover MaintenanceFor assistance, please call 105 106 Specifications and Troubleshooting For assistance, please call 107 Network Camera Reset Procedure-Default Settings 108 Default Settings List For assistance, please call 109 Alarm 110 Items Factory Default Indispensable setting Value Alarm For assistance, please call 111 Items Factory Default Indispensable setting Value Timer Items Factory Default Indispensable setting Value Camera For assistance, please call 113 Preset Buttons Network Camera Specifications Description SpecificationsOther Specification Description Mm 3.46 inches Message Transferring MethodSituation in Buffered Image Quality and the object situation About Network Camera Setup TroubleshootingProblem Cause and Remedy When Top Page does not appear, port number 80 might not be Proxy server may prevent you from connecting directly toWhen you use DDNS, you need to set Default Gateway If Top Page does not appear in the above procedure, press Network window on For Indicator Control windowTransfers older Update About Network Camera Setup Problem Cause and Remedy Lens About Top View Image screen About Other Troubles View Image Setting window on Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information 125 Index Operating Instructions TCP/IP When you ship the product For product service