Update Firmware | Panasonic KX-HCM230 specification

Operating Instructions

3.5.14 Update Firmware

Update Firmware window allows the user to install the latest version of the Network Camera internal operating system. In most cases, this will never be necessary. Changes may be necessary to accommodate new operating systems or new web browsers that are not shown on page 10. In those cases, Update Firmware would be available from the Network Camera Technical Support Site at http://panasonic.co.jp/pcc/en/. Check the current firmware version on Setup Page on page 50.

Notes

•Do not turn off the power during Update Firmware. If the operation of Update Firmware is stopped, refer to page 119.

•Buffered Images are erased when performing Update Firmware.

1.Download the proper firmware from the Network Camera Technical Support Site mentioned above.

2.If Network Camera is accessible from the Internet, temporarily disable access and connect Network Camera to the PC as the following figure. This will eliminate any interruption during the Update Firmware.

Without Ethernet hub, you should use category 5 cross cable.

or

Ethernet hub

Category 5 straight cable

or

Broadband Router

Note

When Network Camera uses the DHCP function, change the Internet connection from DHCP to Static in Network window. Refer to page 54 for the network parameters.

3.Access Setup Page by entering "http://IP Address (or URL):Port No./ config.html" on the web browser and press [Enter].

•When port number is 80 (default), you do not need to enter port number.

[For assistance, please call: 1-800-272-7033]

87

Image 87

Panasonic KX-HCM230 operating instructions Update Firmware

Contents

Network Camera For operation assistance Call Introduction Trademarks Network Camera MemoFor assistance, please call Important Safety Instructions Table of Contents Specifications and Troubleshooting 106 Technical GuidesIndex 125 Section Getting to Know Network Camera Main Features External I/O Input/Output Multi Client AccessUpdate Firmware Authentication System Requirements Authentication window Authentication-System Security Feature AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Included AccessoriesSetup CD-ROM 1 pc Rubber Cap 1 pc Self Bonding tape Connector Cover Setup CD-ROM Fixed Focus Lens Camera Feature LocationsLens Cover Indicator Front View Bottom View Rear View Network Camera Setup Installation Procedure Network Camera Configuration Type Network Camera can be installed on the LAN/IntranetType 2-Internet Connection with a Broadband Router Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PCNetwork Camera can be connected to a PC directly How to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Type Port No Network Camera Configuration TypeDefault Network Parameters Table Click OK to close IP Configuration window How to refer the network parameters from the PC Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Port Forwarding IP Masquerade feature Network Camera Access from the Internet If Top Page does not appear Top Operating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Help Motion JpegSingle Camera Multi-Camera ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Click Delete Deleting the preset buttons Viewing Buffered Image Screen Non Transfer mode Alarm/Timer mode Secondary ViewerClicking Start Capture Primary Multi-Camera Screen Setup Setup Name/Time AdministratorCamera Setup Go to Top Functions of Network Camera Try this option first. Refer to Go to Top Network Enter only the number Instructions for the data fields Or administrator for the Host name If you use Network Camera on the LAN, set upCheck Dhcp Dynamic Host Configuration Protocol Host Name When your ISP uses the Dhcp server function which File size of the image Date Name/TimeCamera Name Time Zone AdjustmentTime Changed AM/PM or 24H Auto Security Administrator Refer to page 61 for details about authentication securityClick Security Administrator on Setup Retype EnableAdministrator and General User Authentication window For Setup Password Security General User Click Security General User on Setup Operating Instructions Top View Image 160 x ResolutionInstructions for the data fields Top Image Image Transfer Non Transfer mode Click Alarm on the Image Transfer window Transfer in the Alarm Mode Active Time of Trigger Alarm enable condition Login timing Data transfer method Over write setting Setting Example Setting explanation Transfer in the Timer Mode Image Frequency Sets the interval to send the image Buffers or transfers by the timer trigger Login timing Over write setting Fixed Camera SetupInstructions for the data fields White Balance Fixed Indoor Tilt Range White Balance is also registered in preset programmingSuggested Having reached the selected end Specifying the Pan/Tilt range Click Save when finished Multi-Camera Camera Name Enable check boxIP Address or URL * 1 or Host External Output Control Click External Output Control on Setup Indicator Control Status Click Cancel to quit. The window returns to the Setup RestartClick Restart Now Update Firmware Click Update Firmware Click Update Firmware on Setup Open Reset to Factory Default Technical Guides Network Camera Installation DC Plug Network Camera Cabling Attach the Sunshade by fastening the two screws Be sure to thread the AC adaptor cord through the hook Inches Cover the putties by rolling Network Camera Mounting Flexible Stand MountingTripod Mounting Wall Mounting Ceiling Mounting Top Bottom Making holes on mortar wall External Sensor Input Interfacing to the External I/OExplanation of External I/O Pin Function Circuit Diagram Example For assistance, please call 103 Ascii and ISO-8859-1 Character TableUnavailable character set Space, , , #, &, %, =, +, ?, , and are not available 104 Displayable character set Maintenance Lens CoverFor assistance, please call 105 106 Specifications and Troubleshooting For assistance, please call 107 Network Camera Reset Procedure-Default Settings 108 Default Settings List For assistance, please call 109 Alarm 110 Items Factory Default Indispensable setting Value Alarm For assistance, please call 111 Items Factory Default Indispensable setting Value Timer Items Factory Default Indispensable setting Value Camera For assistance, please call 113 Preset Buttons Specifications Network Camera Specifications DescriptionOther Specification Description Quality and the object situation Message Transferring MethodMm 3.46 inches Situation in Buffered Image Troubleshooting About Network Camera SetupProblem Cause and Remedy If Top Page does not appear in the above procedure, press Proxy server may prevent you from connecting directly toWhen Top Page does not appear, port number 80 might not be When you use DDNS, you need to set Default Gateway For Indicator Control window Network window onTransfers older Update About Network Camera Setup Problem Cause and Remedy Lens About Top View Image screen About Other Troubles View Image Setting window on Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information 125 Index Operating Instructions TCP/IP When you ship the product For product service