Transfer in the Alarm Mode | Panasonic KX-HCM230 specs

Operating Instructions

Transfer in the Alarm Mode

The Alarm mode can transfer an image via e-mail or FTP when the alarm trigger is active. To activate the alarm trigger, the External Sensor Input of External I/O must be connected with the external sensors/devices. The Alarm mode can send the e-mail without transferring the image. The Alarm mode uses the Network Camera internal clock. Make sure Date and Time has been configured. Refer to page 58 about Date and Time.

1.Click [Alarm] on the Image Transfer window.

a.

b.

c.

d.

e.

f.

68

Image 68

Panasonic KX-HCM230 operating instructions Transfer in the Alarm Mode, Click Alarm on the Image Transfer window

Contents

Network Camera Introduction For operation assistance Call For assistance, please call TrademarksNetwork Camera Memo Important Safety Instructions Table of Contents Index 125 Specifications and Troubleshooting 106Technical Guides Section Main Features Getting to Know Network Camera Multi Client Access Update FirmwareAuthentication External I/O Input/Output System Requirements Authentication-System Security Feature Authentication window Included Accessories Setup CD-ROM 1 pc Rubber Cap 1 pcSelf Bonding tape Connector Cover AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Setup CD-ROM Camera Feature Locations Lens Cover IndicatorFront View Fixed Focus Lens Rear View Bottom View Network Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeNetwork Camera can be installed on the LAN/Intranet Network Camera can be connected to a PC directly Type 3-Internet Direct Connection with a ModemType 4-Direct Connection with a PC How to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera Network Camera Configuration Type DefaultNetwork Parameters Table Type Port No How to refer the network parameters from the PC Click OK to close IP Configuration window Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top If Top Page does not appear Operating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Motion Jpeg Single CameraMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Deleting the preset buttons Click Delete Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Viewer Clicking Start CapturePrimary Secondary Multi-Camera Screen Setup Setup Administrator Camera SetupGo to Top Name/Time Try this option first. Refer to Functions of Network Camera Go to Top Network Instructions for the data fields Enter only the number If you use Network Camera on the LAN, set up Check Dhcp Dynamic Host Configuration ProtocolHost Name When your ISP uses the Dhcp server function which Or administrator for the Host name File size of the image Name/Time CameraName Date Adjustment Time Changed AM/PM or 24HAuto Time Zone Click Security Administrator on Setup Security AdministratorRefer to page 61 for details about authentication security Enable Administrator and General User Authentication windowFor Setup Password Retype Click Security General User on Setup Security General User Operating Instructions Top View Image Resolution Instructions for the data fields TopImage 160 x Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on the Image Transfer window Alarm enable condition Active Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Image Frequency Sets the interval to send the image Login timing Over write setting Camera Setup Instructions for the data fields White BalanceFixed Indoor Fixed White Balance is also registered in preset programming SuggestedHaving reached the selected end Tilt Range Click Save when finished Specifying the Pan/Tilt range Multi-Camera Enable check box IP Address orURL * 1 or Host Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Click Restart Now Click Cancel to quit. The window returns to the SetupRestart Update Firmware Click Update Firmware on Setup Click Update Firmware Open Reset to Factory Default Technical Guides Network Camera Installation Network Camera Cabling DC Plug Be sure to thread the AC adaptor cord through the hook Attach the Sunshade by fastening the two screws Cover the putties by rolling Inches Tripod Mounting Network Camera MountingFlexible Stand Mounting Wall Mounting Ceiling Mounting Top Bottom Making holes on mortar wall Interfacing to the External I/O Explanation of External I/OPin Function External Sensor Input Circuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setSpace, , , #, &, %, =, +, ?, , and are not available For assistance, please call 103 Displayable character set 104 For assistance, please call 105 MaintenanceLens Cover Specifications and Troubleshooting 106 Network Camera Reset Procedure-Default Settings For assistance, please call 107 Default Settings List 108 Alarm For assistance, please call 109 Items Factory Default Indispensable setting Value Alarm 110 Items Factory Default Indispensable setting Value Timer For assistance, please call 111 Items Factory Default Indispensable setting Value Camera Preset Buttons For assistance, please call 113 Other Specification Description SpecificationsNetwork Camera Specifications Description Message Transferring Method Mm 3.46 inchesSituation in Buffered Image Quality and the object situation Problem Cause and Remedy TroubleshootingAbout Network Camera Setup Proxy server may prevent you from connecting directly to When Top Page does not appear, port number 80 might not beWhen you use DDNS, you need to set Default Gateway If Top Page does not appear in the above procedure, press Transfers older For Indicator Control windowNetwork window on About Network Camera Setup Problem Cause and Remedy Update About Top View Image screen Lens View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Index 125 Operating Instructions TCP/IP For product service When you ship the product