Manuals / Panasonic / Photography / Security Camera

Panasonic KX-HCM230 operating instructions Multi-Camera

Models: KX-HCM230

1 128

Download 128 pages 56.99 Kb

Page 81

Operating Instructions

3.5.9 Multi-Camera

Multi-Camera window enables the setting of Multi-Camera screen. Camera Name and IP address of each Network Camera must be entered to view the Multi- Camera screen. Registering IP addresses of the other Network Camera enables you to view on the Multi-Camera screen. Clicking Camera Name of Network Camera on the Multi-Camera screen accesses the Single Camera screen to control the image. First Network Camera is named on Name/Time window on page 58. 2nd to 4th Network Cameras are named on this Multi-Camera window.

Notes

•When using the Multi-Camera screen, all additional Network Cameras must be defined on each Multi-Camera window. This will allow all Network Cameras to be seen and selected from each Network Camera in the entire network.

•Global IP address is required to view the image over the Internet.

1.Click [Multi-Camera]on Setup Page.

[For assistance, please call: 1-800-272-7033]

81

Image 81

Panasonic KX-HCM230 operating instructions Multi-Camera

Contents

Network Camera For operation assistance Call IntroductionTrademarks Network Camera MemoFor assistance, please call Important Safety Instructions Table of Contents Specifications and Troubleshooting 106 Technical GuidesIndex 125 Section Getting to Know Network Camera Main FeaturesUpdate Firmware Multi Client AccessAuthentication External I/O Input/OutputSystem Requirements Authentication window Authentication-System Security FeatureSetup CD-ROM 1 pc Rubber Cap 1 pc Included AccessoriesSelf Bonding tape Connector Cover AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pcSetup CD-ROM Lens Cover Indicator Camera Feature LocationsFront View Fixed Focus LensBottom View Rear ViewNetwork Camera Setup Installation Procedure Network Camera Configuration Type Network Camera can be installed on the LAN/IntranetType 2-Internet Connection with a Broadband Router Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PCNetwork Camera can be connected to a PC directly How to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Default Network Camera Configuration TypeNetwork Parameters Table Type Port NoClick OK to close IP Configuration window How to refer the network parameters from the PCSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Port Forwarding IP Masquerade feature Network Camera Access from the InternetIf Top Page does not appear TopOperating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Single Camera Motion JpegMulti-Camera HelpActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Click Delete Deleting the preset buttonsViewing Buffered Image Screen Non Transfer mode Alarm/Timer modeClicking Start Capture ViewerPrimary SecondaryMulti-Camera Screen Setup Setup Camera Setup AdministratorGo to Top Name/TimeFunctions of Network Camera Try this option first. Refer toGo to Top Network Enter only the number Instructions for the data fieldsCheck Dhcp Dynamic Host Configuration Protocol If you use Network Camera on the LAN, set upHost Name When your ISP uses the Dhcp server function which Or administrator for the Host nameFile size of the image Camera Name/TimeName DateTime Changed AM/PM or 24H AdjustmentAuto Time ZoneSecurity Administrator Refer to page 61 for details about authentication securityClick Security Administrator on Setup Administrator and General User Authentication window EnableFor Setup Password RetypeSecurity General User Click Security General User on SetupOperating Instructions Top View Image Instructions for the data fields Top ResolutionImage 160 xImage Transfer Non Transfer mode Click Alarm on the Image Transfer window Transfer in the Alarm ModeActive Time of Trigger Alarm enable conditionLogin timing Data transfer method Over write settingSetting Example Setting explanation Transfer in the Timer Mode Image Frequency Sets the interval to send the image Buffers or transfers by the timer triggerLogin timing Over write setting Instructions for the data fields White Balance Camera SetupFixed Indoor FixedSuggested White Balance is also registered in preset programmingHaving reached the selected end Tilt RangeSpecifying the Pan/Tilt range Click Save when finishedMulti-Camera IP Address or Enable check boxURL * 1 or Host Camera NameExternal Output Control Click External Output Control on SetupIndicator Control Status Click Cancel to quit. The window returns to the Setup RestartClick Restart Now Update Firmware Click Update Firmware Click Update Firmware on SetupOpen Reset to Factory Default Technical Guides Network Camera Installation DC Plug Network Camera CablingAttach the Sunshade by fastening the two screws Be sure to thread the AC adaptor cord through the hookInches Cover the putties by rollingNetwork Camera Mounting Flexible Stand MountingTripod Mounting Wall Mounting Ceiling Mounting Top Bottom Making holes on mortar wall Explanation of External I/O Interfacing to the External I/OPin Function External Sensor InputCircuit Diagram Example Unavailable character set Ascii and ISO-8859-1 Character TableSpace, , , #, &, %, =, +, ?, , and are not available For assistance, please call 103104 Displayable character setMaintenance Lens CoverFor assistance, please call 105 106 Specifications and TroubleshootingFor assistance, please call 107 Network Camera Reset Procedure-Default Settings108 Default Settings ListFor assistance, please call 109 Alarm110 Items Factory Default Indispensable setting Value AlarmFor assistance, please call 111 Items Factory Default Indispensable setting Value TimerItems Factory Default Indispensable setting Value Camera For assistance, please call 113 Preset ButtonsSpecifications Network Camera Specifications DescriptionOther Specification Description Mm 3.46 inches Message Transferring MethodSituation in Buffered Image Quality and the object situationTroubleshooting About Network Camera SetupProblem Cause and Remedy When Top Page does not appear, port number 80 might not be Proxy server may prevent you from connecting directly toWhen you use DDNS, you need to set Default Gateway If Top Page does not appear in the above procedure, pressFor Indicator Control window Network window onTransfers older Update About Network Camera Setup Problem Cause and RemedyLens About Top View Image screenAbout Other Troubles View Image Setting window onConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information 125 IndexOperating Instructions TCP/IP When you ship the product For product service