Time and Date Adjustment | Panasonic KX-TC1220NZW guide

→

6

1

7 Press (*) to select “AM” or “PM” or 24-hour clock. (Ex. You select “PM”.)

•If numbers between 0000 and 0059, or 1300 and 2359 are entered, the time will automatically be set using the 24-hour clock. Skip the steps 7 and 8 and go to the step 9.

•For AM/PM setting: Enter numbers between 0100 and 1259.

•For 24-hour clock: Enter numbers between 0000 and 2359.

Press á (Next key).

Press á (Next key).

•You may press á (Adjust key) instead.

2

3 Enter the current year by using a 4-digit number.

(Ex. To set the year 2001, enter “2001”.)

4

5 Enter the current time (hour and minute) by using a 4-digit number.

(Ex. To set 9:30, enter “0930”.)

Press á (Set clock key).

•If previously adjusted, “Adjust” will be displayed on the third line.

Lift the handset off the base unit and press /(EXIT/CH) twice.

OR

When the handset is off the base unit, press /(EXIT/CH) once.

Settings

Time and Date Adjustment

You can select AM/PM or 24-hour clock by programming.

Make sure the unit is in the standby mode initially.

12:00A 1.1

→

0000 H=Set clock

12:00A 01.01 Enter year 0000

H=Next

12:00A 01.01 Enter year 2001

H=Next

12:00A 01.01 Enter time

H=Next

09:30A 01.01 Enter time

H=Next

09:30A 01.01 =AM/PM

H=Next

		09:30P	01.01
		=AM/PM
Display	Option		H=Next

A...................... AM

P...................... PM

	→		24-hour clock

Blank display

14•Each time you press (*), the selection will change on the display.

Image 14

Panasonic KX-TC1220NZW Time and Date Adjustment, You can select AM/PM or 24-hour clock by programming

Contents

Charge the battery for about 10 hours before initial use Operating Instructions For your future reference Accessories includedBefore Initial Use Base Unit Location Battery ChargeFor Best Performance Contents Transferring a Call Using the Intercom Call Waiting and Caller ID Compatible For Australia only Location of Controls Handset Base unit Display 0266667777 Preparation Display Settings Connections Battery strength Installing the Battery in the HandsetSettings Display prompt Battery strength Standby mode While the handset is off the base unit Battery informationAfter your Panasonic battery is fully charged p Recharge You can select AM/PM or 24-hour clock by programming Time and Date AdjustmentMake sure the unit is in the standby mode initially For Caller ID service users p To check the time and date During programming Programmable FunctionsTo select the recall time p Points to Program Setting the Auto Talk FeaturePress Ö or Ñ repeatedly until the arrow Press á Yes key With the handset Selecting the Ringer VolumeProgrammable Functions With the base unit Contrast, press á Yes key Setting the LCD ContrastWhile the arrow points to LCD Press Ö or Ñ to select the desired To erase your area code Storing Your Area CodeTo store your area code For New Zealand Users If noise interferes with the conversation Making CallsWith the Handset To redial the last number dialled on the handset Making Calls With the Base Unit Digital Duplex Speakerphone To put a call on hold To adjust the speaker volume 8 levels while talkingTo redial the last number dialled on the base unit To release the hold Simultaneous Keypad Dialling Useful information If the handset is off the base unit, press Talk Answering CallsAuto Talk Talk into the MIC Handset display shows Caller’s phone number after Caller ID ServiceHow caller information is displayed when a call is received ﬁrst ring While the handset is on the base unit Caller ID ServiceTo check the number of new calls While the handset is off the base unit To check who has called, follow the steps below Using the Caller ListViewing the Caller List To exit the list, press EXIT/CH To return to the previous caller Using the Caller ListEx. When you search from the most recent call To exit the Caller List Calling Back from the Caller List Lift the handset off the base unit To erase the number Editing the Caller’s Phone NumberTo add a number Press FUNCTION/EDIT, then press Ü to erase the digit When the caller’s name is not displayed in the Caller List Storing Caller List Information in the Directory Erasing Caller List Information To erase a speciﬁc caller from the Caller List To erase all entries in the Caller List Dialling a Stored Number Speed DiallerStoring Phone Numbers in Memory To erase a stored number Using the Directory Storing Names and Numbers in the Directory For New Zealand Users Number of times key is pressed Keys Selecting Characters to Enter NamesIf you make a mistake while entering a name Eight times Using the DirectoryFor example, to enter Tom Jones Finding Items in the Directory To search for a name by initial Keys Index Dialling from the DirectoryIndex table Editing an Item in the Directory Press Ö or Ñ to select Clear Erasing an Item from the DirectoryDirectory item you want to erase Paging the handset from the base unit Handset locator IntercomPaging the base unit from the handset Handset Press Intercom to answer From the handset to the base unit Transferring a Call Using the IntercomIntercom From the base unit to the handset For Analog PBX Line/Long Distance Service Users Special FeaturesHow to Use the Pause Button Call Waiting and Caller ID Compatible Automatic Security Code SettingSpecial Features Recall Button Desired time is displayed Selecting the recall timePoints to Set recall Wall mounting adaptor, then Wall MountingTuck the telephone line cord inside Push it in the direction of the arrow To charge the handset battery Wall Template That the battery strength indicator appears p Battery ReplacementNew battery for about 10 hours so Close the cover. Make sure you charge Adding Another Phone ProblemRemedy Before Requesting Help Problem Remedy For New Zealand Customers Before Requesting HelpFor Australian Customers Installations Environment Safety InstructionsSafety Placement For New Zealand Users Only Instructions to customer InstallationImportant Information For Australia only Service difficulties PQQX13215ZA-BM S1001-0