Manuals / Panasonic / Communications / Telephone

Panasonic KX-TG7341NZ Error messages, Useful Information, Display message, Cause/solution, Failed

Models: KX-TG7341NZ

1 52

Download 52 pages 20.99 Kb

Page 43

Error messages

Useful Information

Error messages

If the unit detects a problem, one of the following messages is shown on the display.

Display message	Cause/solution
Answer Sys. Full	L Erase unnecessary messages (page 32, 33).
Check Tel Line	L The supplied telephone line cord has not been
	connected yet or not connected properly. Check the
	connections (page 11).
Error	L Recording was too short. Try again.
Failed	L Phonebook copy failed (page 21). Confirm the other
	handset (the receiver) is in standby mode and try
	again.
Incomplete	L The receiver’s phonebook memory is full. Erase the
	unnecessary phonebook entries from the other
	handset (the receiver) and try again.
Memory Full	L The phonebook memory is full. Erase unnecessary
	entries (page 20).
	L Message memory is full. Erase unnecessary
	messages (page 32, 33).
No link to base.	L The handset has lost communication with the base
Reconnect AC	unit. Move closer to the base unit and try again.
adaptor.	L Unplug the base unit’s AC adaptor to reset the unit.
	Reconnect the adaptor and try again.
	L The handset’s registration may have been cancelled.
	Re-register the handset (page 26).
Use rechargeable	L A wrong type of batteries such as Alkaline or
battery.	Manganese was inserted. Use only the rechargeable
	Ni-MH batteries noted on page 3, 12.
You must first	L You must subscribe to a Caller ID service. Once you
subscribe to	receive caller information after subscribing to a Caller
Caller ID.	ID service, this message will not be displayed.

43

Image 43

Panasonic KX-TG7341NZ Error messages, Useful Information, Display message, Cause/solution, Check Tel Line, Failed, adaptor

Contents

Digital Cordless Answering System Charge the batteries for about 7 hours before initial useModel No. KX-TG7341NZ Operating InstructionsPreparation Caller ID ServiceVoice Mail Service IntroductionProduct information Accessory informationSupplied accessories Additional/replacement accessoriesIntroduction Expanding your phone systemHandset optional KX-TGA731AZ Operating safeguards For your safetyPower connection InstallationBattery General noticesIntroduction Important notice Important safety instructionsFor best performance IntroductionInformation on Disposal in other Countries outside the European Union IntroductionRoutine care Notice for product disposal, transfer, or returnPreparation ControlsBase unit HandsetSoft keys DisplayUsing the navigator key PreparationBase unit ConnectionsDuring a power failure If you subscribe to a DSL/ADSL servicePreparation Battery installation and replacementBattery level Battery chargeBattery level Battery iconWall mounting Turning the power on/offSetting up the unit before use Symbols used in these operating instructionsPreparation Date and time2 V/ “Handset Setup” 3 V/ “Time Settings”Making calls Using the handsetUsing the base unit Pause for PBX/long distance service usersAdjusting the base unit ringer volume Answering callsUsing the handset Using the base unitRecall/flash Useful features during a callFor call waiting or Call Waiting Caller ID service users MuteCall privacy Handset Handset key lockMaking/Answering Calls Editing entries Handset phonebookAdding entries Finding and calling a phonebook entryCopying an entry Copying phonebook entriesChain dial Handset phonebookBase unit speed dial Making a call using the speed dial keysBase unit speed dial Adding phone numbers to speed dialHandset Setup Programmable settingsProgramming by scrolling through the display menus ProgrammingSub-menu ProgrammingTop-menu Sub-menu2 V/ “Handset Setup” Special instructions for programmable settingsAlarm Time adjustment Caller ID subscribers onlyOperating additional units Registering a unitSelecting area codes to be deleted automatically Changing the base unit PIN Personal Identification Number2 V/ “Base Unit Setup” Increasing the range of the base unit2 V/ “Base Unit Setup” Setting the repeater modeUsing toll services from Telecom or another company Using Caller ID serviceCaller ID features Caller ID ServiceErasing caller information Caller listViewing the caller list and calling back Editing a caller’s phone number before calling backCall screening Answering systemTurning the answering system on/off Memory capacityPlaying back the greeting message Using a pre-recorded greeting messageGreeting message Recording your greeting messageErasing all messages Listening to messages using the base unitListening to messages using the handset Operating the answering systemOperation Calling back Caller ID subscribers onlyErasing all messages Answering SystemTurning on the answering system remotely Using the answering system remotelyRemote commands Voice guidance2 V/ “Answer System” Answering system settingsNumber of rings before the unit answers a call Answering System2 V/ “Answer System” Caller’s recording timeCall screening Answering SystemVoice Mail Service Voice mail serviceAnswering an intercom call IntercomTransferring calls Making an intercom callBase unit Intercom/LocatorBase unit Transferring a call without speaking to the other unit’s user HandsetHandset Conference callsHandset locator Intercom/LocatorUseful Information Character entryCharacter entry modes Characters available in each character entry modeCyrillic character table P Useful InformationExtended 1 character table N Extended 2 character table Obattery Error messagesCause/solution ErrorUseful Information TroubleshootingProblem Cause/solutionBattery recharge Programmable settingsProblem Cause/solutionMaking/answering calls, intercom ProblemCause/solution Useful InformationCause/solution ProblemCause/solution ProblemCause/solution ProblemCause/solution ProblemVoice coding ADPCM 32 kbit/s Power source 220-240 V AC, 50/60 Hz SpecificationsDuplex procedure RF transmission powerIndex IndexPage Customer Support Centre Tel. No PNQX1229ZA CC0908DJ0For your future reference Attach your purchase receipt here