Panasonic PT-L780E, PT-L780NTE manual Starting to use, Turning on the power, Turning off the power

Starting to use

Turning on the power

Please ensure that all preparations have been completed before turning on the power. (Refer to pages 22 – 27.)

#Remove the lens cover.

$Connect the accessory mains lead.

*Press the FOCUS +/- or ZOOM +/- buttons to adjust the projected image focus and size.

The projected image focus can also be adjusted by turning the focus ring. To make fine adjustments to the projected image focus, use the FOCUS +/- buttons.

	RGB INPUT	LAMP	TEMP
		INPUT
POWER	AUTO SETUP	VIDEO	RGB SHUTTER
STANDBY(R)
ON(G)
– FOCUS +
– ZOOM +	MENU		ENTER

Focus

%Press the MAIN POWER switch to
the “l” side to turn on the power.									%
The power indicator on the projector				$
will illuminate red.
&Press the POWER button.
The power indicator on the projector				RGB INPUT	LAMP	TEMP
					INPUT
			POWER	AUTO SETUP	VIDEO	RGB	SHUTTER	AUTO
will flash green. After a short period,								POWER SETUP
								RGB LASER
			STANDBY(R)
the indicator will illuminate green, and			ON(G)					VIDEO MENU
			– FOCUS +					PAGE
a picture will be projected.			– ZOOM +	MENU			ENTER
'Press the input select (RGB, VIDEO)				RGB INPUT	LAMP	TEMP
button to select the input signal.					INPUT				AUTO
			POWER	AUTO SETUP	VIDEO	RGB	SHUTTER	POWER SETUP
								RGB	LASER
The input signal selected will change			STANDBY(R)					VIDEO	MENU
			ON(G)
			– FOCUS +					PAGE
as shown at below each time an input
			– ZOOM +	MENU			ENTER
select button is pressed.
				SD CARD
VIDEO VIDEO	RGB	RGB		NETWORK
				DVI
			RGB3
S-VIDEO			RGB2
VIDEO			RGB1
(While pressing the adjuster buttons,
adjust the forward/back angle of tilt
of the projector.
To make fine adjustments to the angle of
tilt of the projector, turn the front
adjustable legs. (The front adjustable legs
will be locked if they are fully extended
and then turned anticlockwise. Turn them
back clockwise to release the lock.)
)Press the AUTO SETUP button to
initiate automatic positioning.				RGB INPUT	LAMP	TEMP
					INPUT
The automatic positioning is only for vertical			POWER	AUTO SETUP	VIDEO	RGB	SHUTTER		AUTO
								POWER SETUP
								RGB	LASER
keystone distortion. To correct the			STANDBY(R)
			ON(G)					VIDEO	MENU
			– FOCUS +					PAGE
horizontal keystone distortion or when
keystone distortion has not been corrected			– ZOOM +	MENU			ENTER
to the optimum level, carry out the keystone
correction as described on page 40.

Turning off the power
#Press the POWER button. “Power
		Power OFF
OFF” is displayed on the screen.
$Select “OK” using the I and H	OK		CANCEL
buttons and press the ENTER button.

The lamp unit will switch off and the picture will stop being projected. (The power indicator on the projector will illuminate orange.)

%Wait until the power indicator on the projector illuminates red (until the cooling fan stops).

Do not in any way cut power to the projector while the cooling fan is still operating. Be careful not to switch off the MAIN POWER switch of the projector, unplug the mains lead from the electrical outlet or turn off in-line switches such as tabletop power switches.

&Press the MAIN POWER switch to the “O” side to turn off the power.

NOTE:

BAfter the power is turned off, the lamp unit will take some time to cool down. If you turn the power back on again before the lamp unit has cooled down, the lamp unit may not turn on straight away, but it will turn on automatically after a short period. (During this time, the power indicator on the projector will flash orange.)

BWhen the projector is in standby mode (the power indicator on the projector is illuminated red), the projector will still draw a maximum 3.5 W of power, even when the cooling fan has stopped.

BIf the MAIN POWER switch is accidentally turned off while the projector is being used, the lamp unit may not turn on straight away after the power is turned back on. In such cases, the lamp unit will turn back on automatically after a short period. (During this time, the power indicator on the projector will flash green.)

BA tinkling sound may be heard while the power indicator is turned off, but this is not a sign of a malfunction.

BYou can also turn off the power by pressing the POWER button twice.

BWhen the WEB STANDBY is set to “ON”, the cooling fan operates and the power indicator on the projector flashes slowly in red and the projector draw a maximum 43 W of power. (page 45) (PT-L780NTE only)

BDo not turn off the power while the SD card is being accessed and “SD card is in use.” is displayed on the screen. (PT-L780NTE only)

Basic Operation

28-ENGLISH ENGLISH-29