Panasonic PT-L750U R, TQBH9003-6 Turning off the power

31

Basic Operation

RGBVIDEOAUTO SETUP

ON(G)

STANDBY(R)

ENTER

MENU

POWER SHUTTER

INPUT

TEMP

LAMPRGB INPUT

– FOCUS +

– ZOOM +

*

Press the FOCUS +/- or ZOOM

+/- buttons to adjust the

projected image focus and size.

The projected image focus can

also be adjusted by turning the

focus ring. To make fine

adjustments to the projected

image focus, use the FOCUS +/-

buttons.

Focus

Turning off the power

#Press the POWER button. “Power

OFF” is displayed on the screen.

$Select “OK” using the IIand HH

buttons and press the ENTER button.

The lamp unit will switch off and the picture will stop being projected. (The

power indicator on the projector will illuminate orange.)

%Wait until the power indicator on the projector illuminates red (until

the cooling fan stops).

Do not in any way cut power to the projector while the cooling fan is still

operating. Be careful not to switch off the MAIN POWER switch of the

projector, unplug the power cord from the electrical outlet or turn off in-line

switches such as tabletop power switches.

&Press the MAIN POWER switch to the “O” side to turn off the power.

NOTE:

BAfter the power is turned off, the lamp unit will take some time to cool

down. If you turn the power back on again before the lamp unit has cooled

down, the lamp unit may not turn on straight away, but it will turn on

automatically after a short period. (During this time, the power indicator on

the projector will flash orange.)

BWhen the projector is in standby mode (the power indicator on the

projector is illuminated red), the projector will still draw a maximum 3.5 W

of power, even when the cooling fan has stopped.

BIf the MAIN POWER switch is accidentally turned off while the projector is

being used, the lamp unit may not turn on straight away after the power is

turned back on. In such cases, the lamp unit will turn back on

automatically after a short period. (During this time, the power indicator on

the projector will flash green.)

BA tinkling sound may be heard while the power indicator is turned off, but

this is not a sign of a malfunction.

BYou can also turn off the power by pressing the POWER button twice.

BWhen the WEB STANDBY is set to “ON”, the cooling fan operates and

the power indicator on the projector flashes slowly in red and the projector

draw a maximum 43 W of power. (page 47) (PT-L780NTU only)

Power OFF

OK CANCEL

Contents

Main Operating Instructions IMPORTANT SAFETY NOTICE Dear Panasonic Customer: Page Contents Contents (Network Functions, SD Card Functions) Fitting and removal of SD card and wireless card ..................90 How to use SD card...............92 Network setting .....................99 Web browser control...........116 Precautions with regard to safety Page Page Page Notes with regard to the wireless card and the projector. Accessories Precautions on handling Cautions when moving the projector Cautions regarding setting-up Notes on use Page Location and function of each part Projector <Top, right and front> Projector <Back and bottom> Remote control unit Projector control panel Page <Connector panel> <SD memory card><Card slot> Using the remote control unit Laser beam pointer Wireless mouse standard mouse driver which comes bundled with the operating system. Move the mode switch to the Computer position. Inserting the batteries Operating range Setting the projector IDs number for remote control unit Connections Notes on connections Page Example of connecting to video equipments Example of connecting to computer Setting-up Projection methods Projector position Projection distances Make sure that enough space is kept for the air outlet port. $ % Starting to use Turning on the power Turning off the power PICTURE menu (page 38) When an RGB/DVI signal is being input On-screen menus Menu screens NOTE: BKeystone distortion of the on-screen display will not be corrected. When a YPBPRsignal is being input When an S-VIDEO/VIDEO signal is being input POSITION menu (page 41) When an RGB/DVI signal is being input When a YPBPRsignal is being input LANGUAGE menu (page 45) When the NETWORK/SD CARD is selected (PT-L780NTU only) AUDIO menu (page 45) NETWORK menu (page 49) (PT-L780NTU only) OPTION menu (page 46) LENS menu (page 50) SD CARD menu (page 49) (PT-L780NTU only) The RGB/YPbPr item is displayed when an RGB/YPBPRsignal is being input. Menu operation guide Returning to the previous screen Returning a setting to the factory default displayed Using the freeze function Using the D.ZOOM (digital zoom) function Adjusting the picture DYNAMIC NATURAL PICTURE MODE Color Hue Setting (color temperature) COLOR TINT BRIGHT CONTRAST WHITE BALANCE R/G/B Projecting sRGB- compatible pictures Adjusting the position POSITION DOT CLOCK CLOCK PHASE KEYSTONE OSD POSITION ASPECT AUTO 4:3 16:9 S4:3 RESIZING AUTO SETUP FRAME LOCK Audio adjustment VOLUME MUTE Changing the display language SHUTTER Option settings BACK COLOR FRONT/REAR DESK/CEILING LAMP POWER LAMP RUN TIME WEB PASSWORD CONTROL KEY FUNC 1 SET ID AUTO POWER OFF NETWORK SETUP STATUS WEP SD CARD SETUP AUTO PLAY Lens adjustment LENS SELECT Projection lens replacement Removing the lens Installing the lens Projection distance for each projection lens (sold separately) Projector position ET-LE10 (for short-distance projection) ET-LE20 (for medium-distance projection) ET-LE30 (for long-distance projection) Slot cover replacement Removing the slot cover Installing the slot cover Putting the power cord and remote control unit away Removing the cable cover Installing the cable cover NOTE: Do not lift up the projector by holding the cable, otherwise the cable cover might come off. Using the cable cover # Using the remote terminal Pin assignment and control Using the SERIAL connector Connection Pin layout and signal names for SERIAL connector Basic format Communications settings Control commands Cable specifications Indicators Page About the automatic setup function List of compatible signals Cleaning and replacing the air filter Cleaning procedure Replacing the lamp unit Notes on replacing the lamp unit Lamp unit replacement period Lamp unit replacement procedure Page Before calling for service Before calling for service, check the following points. Problem Possible cause Problem Possible cause Specifications FCC class B Trademark acknowledgements Dimensions NOTES IMPORTANTES CONCERNANT LA SCURIT Prcautions de scurit Page Page Page Prcautions de manipulation Prcautions prendre lors du dplacement du projecteur Avertissements concernant linstallation Notes sur lutilisation Page Remplacement du bloc de lampe Notes sur le remplacement du bloc de lampe Priode de remplacement du bloc de lampe Mthode de remplacement du bloc de lampe Page Page Instructions on handling Instruction on storage For protection of important data Other instructions Precautions on use of SD card Please be advised of the following information in advance: To create a backup copy of the data stored on the SD card Write protection switch Radio frequencies used by the wireless card Do not use the cards near other sources of radio emissions. Precautions on use of projector LAN card Available channels Typical applications of SD card / network functions Examples of use of SD card Writing data directly on SD card using personal computer Projecting images from SD card using the projector only Example of use of network functions Projecting images from SD card using Web browser control Controlling the projector using Web browser control Fitting and removal of SD card and wireless card SD card Removal Fitting Wireless card/Projector LAN card Fitting Removal How to use SD card Setting AUTOPLAY REPEAT INTERVAL Replay Recording directly on SD card Compiling on Windows Fitting SD card Page Removing SD card Compilation on Macintosh machine Fitting SD card Saving images in Macintosh onto the SD card. Removing SD card Network setting Example of setting for use of the wireless card To use wireless communication for the first time If wireless communication has already been established between PCs (in ad hoc mode) Setting of the projectorParameters If wireless communication has already been established using an access point Setting of the projector LAN Setting of the projector If communication in ad hoc mode is unavailable To directly connect a personal computer to the projector Example of setting for use of the projector LAN card When connecting via a relaying device Setting up the projector Mounting a wireless card qqInsert the wireless card into the projector Status WEP Wired Equivalent Privacy Gateway Host name Mode SSID (in INFRASTRUCTURE mode or in PEER TO PEER mode only) Channel Mounting a projector LAN card WEP setup wizard Installing a wireless card driver Fitting and removal of wireless card into/from personal computer Insertion of wireless card Removal of wireless card Installing a driver For Windows98SE For Windows2000 For WindowsXP Settings of wireless card Settings of personal computer TCP/IP setting For Windows98SE For WindowsXP For Windows2000 If two or more network devices are existent For Windows98SE Page Web browser control What you can do with Web browser control Settings of Web browser control Settings of projector Web control Operation of Web browser control Starting Web browser control Top screen Projector control Click "Projector control" in the menu. Basic control screen Option control screen Monitor information screen SD control It is also possible to switch to it on the basic control screen of the projector control. wwClick "SD control" in the menu. SD file list screen SD thumbnail screen When using PDA Operation of PDA Top screen Starting the Web browser control (PDA) Start the browsing software and enter the following address: SD control Projector control Menu screen Wireless Manager 2.0 What you can do with Wireless Manager 2.0 Installation of Wireless Manager 2.0 Before installation Procedure of installation Operation of Wireless Manager 2.0 Starting/ending Wireless Manager 2.0 Registration of projector Page To capture and transfer the image of PC screen Before transmitting an image Functions on the "Capture" window 1. "Full screen" button 2. "Area" button Transfer of image stored in the personal computer The functions on "Image List" screen 1. Choosing an image folder 2. "Add" button Page Page Major examples of usage Basic usage Automatic display in predefined sequence Quick-changing presentation using SD card Conference using multiple personal computers Image Creator 1.0 What you can do with Image Creator 1.0 Installation of Image Creator 1.0 Before installation Procedure of installation Operation of Image Creator 1.0 Starting/ending Image Creator 1.0 Converting and saving captured images Capturing presentation files created with Microsoft PowerPoint97/2000/2002 qqPress the "Capture slides" button and select the presentation files you want to capture. Capturing JPEG, BMP, TIFF or PNG files created with other applications Press the "Capture images" button and select the images or folders you want to capture. Images not to be captured Capturing files by drag-and-drop operation Sorting images Deleting images Setting how to convert images when saving Page DCF standard Directory (folder) name File name File format Before placing an repair order Please make sure of the following: Symptom Please check: Explanation of terms Access Point Channel SSID WEP JPEG RLE TIFF LZW DCF Exif 2.1 Trademark Information Consignes de scurit propos de la carte de radiocommunication et du projecteur Frquences radio utilises par la carte de radiocommunication Canaux disponibles Remarque: