Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic Model 3101RC manual Firmware Write In Progress, Firmware Write Successful

Models: Model 3101RC

1 47

Page 37

Model 3101RC Getting Started Guide	3 • Configuration

Firmware Write In Progress

The Flash Write process may take a few minutes. You must not turn off or reset the system during the pro- cess.

Firmware Write Successful

When the Flash Write process has completed successfully, the Firmware Update Status shows “Firmware has upgraded already”. You can now restart the system.

Firmware Update

Page 37

Image 37

Patton electronic Model 3101RC manual Firmware Write In Progress, Firmware Write Successful

Contents

Model 3101RC ADSL2/2+ Triple-Play Access IPDSLAM ModuleGetting Started Guide Sales Ofﬁce +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Hardware Installation Summary Table of ContentsConfiguration Model 3101RC OverviewSummary Table of Contents Table of ContentsTable of Contents Hardware Installation5 Contacting Patton for assistance OperationCompliance information Model 3101RC Getting Started GuideList of Figures Required Installation Tools and Materials List of TablesFirmware Update Procedure Required Installation Tools and MaterialsAudience About this guideStructure Safety when working with electricity PrecautionsGeneral conventions Typographical conventions used in this documentMouse conventions Chapter 1 Model 3101RC Overview Chapter contentsFigure 1. Model 3101RC ADSL2/2+ Triple-play Access IPDSLAM Module IntroductionApplications FeaturesFigure 2. 3101RC application Chapter Hardware InstallationChapter contents Safety Requirement Pre-InstallationTools and Test Equipment Requirements Electrostatic Discharge ProtectionConnecting the ADSLx interfaces Hardware InstallationRJ-45 Electrical Trunk Port Connecting the GBE trunk interfaceTX + Ethernet Port 10/100 ENET on Trunk CardRX + LED AConsole Port CONFIG Chapter contents ConﬁgurationChapter Provisioning a Management IP Port Then, type the following commands to change in-band or out-band IP settings as you want Web GUI Figure 12. Select Database Conﬁguration Figure 11. IP RoutesFigure 13. Save Running Conﬁg to Flash Example Conﬁguration Import/ExportExample Figure 14. DB Conﬁguration ConceptExample ExampleExample ExampleWeb GUI A - Import File Write Download Conﬁg To FlashConfiguration Import/Export 3 ConfigurationWrite downloaded Conﬁg to Flash in progress Write to memory successfully3 Configuration B - Import File Load Remote Conﬁg to Running ConﬁgConfiguration Import/Export Figure 20. Load Remote Conﬁg to Running Conﬁg Get File3 Configuration C - Export File Put Running Conﬁg to Remote TFTP ServerConfiguration Import/Export TFTP put ﬁle successfully3 Configuration D - Save Running Conﬁg to Flash System ConﬁgConfiguration Import/Export Write running conﬁg to Flash successfully3 Configuration E - Reload FLASH to Running ConﬁgConfiguration Import/Export Load conﬁguration from FLASH to Running Conﬁg successfullyFigure 30. Restore Factory Default F - Restore Factory DefaultFigure 31. Restore Successful Figure 32. Flash Boot Point Conﬁguration Select G - Flash Boot Point Conﬁguration SelectFirmware Update Firmware UpdateExample Web GUI FTP Get In ProgressEnter the following parameters Firmware Write Successful Firmware Write In ProgressChapter contents OperationChapter Dispatching Maintenance Personnel Maintenance RequirementRoutine Maintenance Tools and Equipment Requirements3101RC LEDs Controls and LED Indication10/100 ENET CONFIGSpeed right LED onModel 3101TM 3101TM LEDsChapter contents Chapter 5 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsOut-of-warranty service Contact informationRMA numbers Return for credit policyShipping instructions Patton Electronics CompanyChapter contents Appendix A Compliance informationCompliance Safety ComplianceCE Declaration of Conformity EMC Compliance