Manuals / Paxar / Computer Equipment / Printer

Paxar 9855 RFID R F I D S u p p l y S p e c i f i c a t i o n s, T a g C u t D i m e n s i o n s

Models: 9855 RFID

1 24

Download 24 pages 50.86 Kb

Page 21

R F I D S u p p l y S p e c i f i c a t i o n s

R F I D S u p p l y S p e c i f i c a t i o n s

RFID supplies are available in a variety of sizes. Printing over the RFID inlay causes printing irregularity. Refer to the RFID Setup Guide & Supply Chart or the HF Setup Guide & Supply Chart for illustrations to determine which type of RFID supplies you are using and basic printer configuration information.

Supply Types:	Thermal Transfer or Thermal Direct
	Die Cut or Black Mark
Supply Widths:	0.75 inch (19 mm) minimum
	4.0 inches (102 mm) maximum
Supply Lengths:	1.0 inch (25.4 mm) minimum
	13.0 inches (330 mm) maximum
	Note: The supply length depends on the inlay selected.
Roll Inside	4.0 inches (102 mm)
Diameter:
Roll Outside	8.0 inches (203 mm) maximum
Diameter:
Ribbon Width:	4.3 inches (110 mm) for 4.0 inch (102 mm) supply
Ribbon Length:	23,600 inches (600 meters)

Additional RFID supplies may be available by request. Contact your RFID Representative for more information.

T a g C u t D i m e n s i o n s

Use these specifications for the 926™ Knife with the RFMP printer. Use only Monarch→/Paxar→ approved RFID tag supplies.

Widths:	1.5	inches to 4.0 inches (38 mm to 102 mm)
Lengths:	1.5	inches to 16.0 inches (38 mm to 406 mm)
Thickness:	7 mils to 14 mils
Batch Separator:	3.66 inches (93 mm)

Note: The limited warranty on knives used in or with RFID printers is one (1) year from the date of shipment, or 500,000 cuts, whichever occurs first.

19

Image 21

Paxar 9855 RFID manual R F I D S u p p l y S p e c i f i c a t i o n s, T a g C u t D i m e n s i o n s

Contents

Quick Reference Monarch 9855 RFID PrinterTC9855RFIDQR Rev. AN 4/08 Trademarks I n t r o d u c t i o n R F I D O v e r v i e wA b o u t P r o f e s s i o n a l S e r v i c e s C o n n e c t i n g t h e C a b l e s W e b S i t e s w i t h R F I D I n f o r m a t i o nPower U s i n g t h e C o n t r o l P a n e lFault Feed/CutL o a d i n g R F I D L a b e l s 6. Push down on the supply lever to unlock the supply guides Die Cut Sensor DeflectorSupply Roller NibsLoading Labels for the Optional Peel Mode A d j u s t i n g t h e W i d e / N a r r o w K n o b s L o a d i n g R i b b o n Printhead Tab Deflector TabTake-up Core Take-up Reel Ribbon Rollers P r i n t i n g A d j u s t i n g t h e P r i n t C o n t r a s tM e n u C h a n g e s C l e a r i n g J a m s C l e a n i n gVoids Streaks If the brush does not remove T r o u b l e s h o o t i n g ProblemAction Supply Chart or HF Setup Guide & Supply Chart C o m m o n E r r o r s412 Flow control mismatch 413 Online receive buffer is full. Check for a flow control problem611 Font, bar code, or density in the batch does not fit the format 613 Reference point off supply753 Printer sensed a mark that is too long 752 Printer sensed a mark in the wrong place755 Printhead is open. Close the printhead 756 Load supplies 757 Load supplies supply length mismatch. Press Feed/CutWeight R F I D P r i n t e r S p e c i f i c a t i o n sShipping Weight Power SourceT a g C u t D i m e n s i o n s R F I D S u p p l y S p e c i f i c a t i o n sR F S p e c i f i c a t i o n s