Manuals / Paxar / Computer Equipment / Printer

Paxar Sierra Sport3 C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e s, Screws

Models: Sierra Sport3

1 46

Page 11

C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e s

9-pin serial communication cables and USB cables are available. For best results, use only Monarch® cables. See Appendix B, "Accessories" for part number information.

Open the hinged cable door by loosening the two Philips screws and lifting up on the door.

Screws

Getting Started 1-7

Page 11

Image 11

Paxar Sierra Sport3 manual C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e s, Screws

Contents

All rights reserved Operator’s HandbookMonarch 9433 Sierra Sport3 Printer TC9433OH Rev. AD 12/07Trademarks CANADIAN D.O.C. WARNINGSPECIFICATIONS T A B L E O F C O N T E N T SCARE & MAINTENANCE TROUBLESHOOTINGPRINTER OPTIONS ACCESSORIESA u d i e n c e G E T T I N G S TA R T E DU s i n g T h i s M a n u a l U n p a c k i n g t h e P r i n t e r A d d i t i o n a l D o c u m e n t a t i o nP r i n t e r U t i l i t i e s I n s t a l l i n g t h e B a t t e r y Ready p 1-4 Operator’s Handbook 2 . Insert the connector end of the battery into the printer3 . Close the supply door until the release levers click into place Battery and Safety Information Do not let the battery get wet or come into contact with metal objects Screws C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e s2 . Place the cable in the cable cavity Serial Cable1 . Plug the DB9 connector into the DB9 port ConnectorUSB Port USB Cable Cable in Cable Cavity USB Cable1 . Plug the USB cable into the USB port 3 . Closed the hinged cable door and tighten the screwsButtons U s i n g t h e D i s p l a y a n d B u t t o n sNavigation DisplayP r i n t i n g 1-12 Operator’s Handbook non-peel mode prints a continuous strip of supply L O A D I N G S U P P L I E SThis chapter describes how to load supply for The printer may be on or off when loading suppliesL o a d i n g f o r N o n - P e e l M o d e Exit Chute Supply Holder TabsTearing the Supplies L o a d i n g f o r P e e l M o d e Peel roller 2-6 Operator’s HandbookPeel bar Label Liner 6. Close the supply door until the release levers click into place7. Lightly tug on the liner to remove the slack The liner separates from the label2-8 Operator’s Handbook L o a d i n g F a n - F o l d S u p p l i e sLoading Supplies 8. Close the supply door until the release levers click into placeTear Edge Tearing the Supplies2-10 Operator’s Handbook C l e a n i n g C A R EM A I N T E N A N C E Use any of the following items to clean the printhead Printhead On-Demand Sensor Turn the platen roller with your finger to clean the entire surface C l e a r i n g L a b e l J a m s 3-6 Operator’s Handbook “Care and Maintenance” for more T R O U B L E S H O O T I N GProblem Solution2710 C o m m o n E r r o r sError DescriptionDescription ErrorDescription ErrorS P E C I F I C AT I O N S P r i n t e r S p e c i f i c a t i o n sRelative Humidity Battery and Printer 5% to 90% non-condensingOperating Limits 32 to 109 F 0 to 43 C PrinterStorage 14 to 122 F -10 to 50 CSupply Widths 0.5 13 mm minimum 2.99 76 mm maximum S u p p l y S p e c i f i c a t i o n sC a b l e P i n - o u t s Supply Types Labels, tags, or receipt paperA-4 Operator’s Handbook A C C E S S O R I E S B-2 Operator’s Handbook S i n g l e S t a t i o n B a t t e r y C h a r g e rF o u r S t a t i o n B a t t e r y C h a r g e r C a r r y i n g A c c e s s o r i e sB l u e t o o t h P R I N T E R O P T I O N S CL i n e r l e s s C-2 Operator’s Handbook