Manuals / Paxar / Computer Equipment / Printer

Paxar Sierra Sport3 manual C l e a r i n g L a b e l J a m s

Models: Sierra Sport3

1 46

Download 46 pages 33.59 Kb

Page 31

C l e a r i n g L a b e l J a m s

When you are printing and a jam occurs, a supply error message appears. To clear the jam:

1. Turn off the printer by pressing and holding P until the display is blank.

2. Pull the release levers located on both sides of the printer to open the supply door.

3. If necessary, remove the roll of supplies.

4. Remove the jammed supplies and reload the supply.

5. Close the supply door until the release levers click into place.

6. Turn on the printer by pressing and holding P until the display turns on.

Care & Maintenance 3-5

Image 31

Paxar Sierra Sport3 manual C l e a r i n g L a b e l J a m s

Contents

All rights reserved Operator’s HandbookMonarch 9433 Sierra Sport3 Printer TC9433OH Rev. AD 12/07Trademarks CANADIAN D.O.C. WARNINGSPECIFICATIONS T A B L E O F C O N T E N T SCARE & MAINTENANCE TROUBLESHOOTINGPRINTER OPTIONS ACCESSORIESU s i n g T h i s M a n u a l G E T T I N G S TA R T E DA u d i e n c e P r i n t e r U t i l i t i e s A d d i t i o n a l D o c u m e n t a t i o nU n p a c k i n g t h e P r i n t e r I n s t a l l i n g t h e B a t t e r y 3 . Close the supply door until the release levers click into place 2 . Insert the connector end of the battery into the printerReady p 1-4 Operator’s Handbook Battery and Safety Information Do not let the battery get wet or come into contact with metal objects Screws C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e s2 . Place the cable in the cable cavity Serial Cable1 . Plug the DB9 connector into the DB9 port ConnectorUSB Port USB Cable Cable in Cable Cavity USB Cable1 . Plug the USB cable into the USB port 3 . Closed the hinged cable door and tighten the screwsButtons U s i n g t h e D i s p l a y a n d B u t t o n sNavigation DisplayP r i n t i n g 1-12 Operator’s Handbook non-peel mode prints a continuous strip of supply L O A D I N G S U P P L I E SThis chapter describes how to load supply for The printer may be on or off when loading suppliesL o a d i n g f o r N o n - P e e l M o d e Exit Chute Supply Holder TabsTearing the Supplies L o a d i n g f o r P e e l M o d e Peel bar 2-6 Operator’s HandbookPeel roller Label Liner 6. Close the supply door until the release levers click into place7. Lightly tug on the liner to remove the slack The liner separates from the label2-8 Operator’s Handbook L o a d i n g F a n - F o l d S u p p l i e sLoading Supplies 8. Close the supply door until the release levers click into place2-10 Operator’s Handbook Tearing the SuppliesTear Edge M A I N T E N A N C E C A R EC l e a n i n g Use any of the following items to clean the printhead Printhead On-Demand Sensor Turn the platen roller with your finger to clean the entire surface C l e a r i n g L a b e l J a m s 3-6 Operator’s Handbook “Care and Maintenance” for more T R O U B L E S H O O T I N GProblem Solution2710 C o m m o n E r r o r sError DescriptionDescription ErrorDescription ErrorS P E C I F I C AT I O N S P r i n t e r S p e c i f i c a t i o n sRelative Humidity Battery and Printer 5% to 90% non-condensingOperating Limits 32 to 109 F 0 to 43 C PrinterStorage 14 to 122 F -10 to 50 CSupply Widths 0.5 13 mm minimum 2.99 76 mm maximum S u p p l y S p e c i f i c a t i o n sC a b l e P i n - o u t s Supply Types Labels, tags, or receipt paperA-4 Operator’s Handbook A C C E S S O R I E S B-2 Operator’s Handbook S i n g l e S t a t i o n B a t t e r y C h a r g e rF o u r S t a t i o n B a t t e r y C h a r g e r C a r r y i n g A c c e s s o r i e sL i n e r l e s s P R I N T E R O P T I O N S CB l u e t o o t h C-2 Operator’s Handbook