Manuals / Paxar / Computer Equipment / Printer

Paxar Sierra Sport3 manual Operator’s Handbook, Peel bar, Peel roller

Models: Sierra Sport3

1 46

Download 46 pages 33.59 Kb

Page 22

Peel bar

Note: The supply should unwind from the top with the loose end of the supply feeding through the exit chute.

4. Raise the peel tabs on both sides of the printer.

5. Remove a couple of labels from the liner. Feed the liner over the platen roller, over the peel bar, and under the peel roller.

Peel bar

Raised peel tab

Peel roller

2-6Operator’s Handbook

Image 22

Paxar Sierra Sport3 manual Operator’s Handbook, Peel bar, Peel roller

Contents

TC9433OH Rev. AD 12/07 Operator’s HandbookMonarch 9433 Sierra Sport3 Printer All rights reservedCANADIAN D.O.C. WARNING TrademarksTROUBLESHOOTING T A B L E O F C O N T E N T SCARE & MAINTENANCE SPECIFICATIONSACCESSORIES PRINTER OPTIONSU s i n g T h i s M a n u a l G E T T I N G S TA R T E DA u d i e n c e P r i n t e r U t i l i t i e s A d d i t i o n a l D o c u m e n t a t i o nU n p a c k i n g t h e P r i n t e r I n s t a l l i n g t h e B a t t e r y 3 . Close the supply door until the release levers click into place 2 . Insert the connector end of the battery into the printerReady p 1-4 Operator’s Handbook Battery and Safety Information Do not let the battery get wet or come into contact with metal objects C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e s ScrewsConnector Serial Cable1 . Plug the DB9 connector into the DB9 port 2 . Place the cable in the cable cavity3 . Closed the hinged cable door and tighten the screws USB Cable1 . Plug the USB cable into the USB port USB Port USB Cable Cable in Cable CavityDisplay U s i n g t h e D i s p l a y a n d B u t t o n sNavigation ButtonsP r i n t i n g 1-12 Operator’s Handbook The printer may be on or off when loading supplies L O A D I N G S U P P L I E SThis chapter describes how to load supply for non-peel mode prints a continuous strip of supplyL o a d i n g f o r N o n - P e e l M o d e Supply Holder Tabs Exit ChuteTearing the Supplies L o a d i n g f o r P e e l M o d e Peel bar 2-6 Operator’s HandbookPeel roller The liner separates from the label 6. Close the supply door until the release levers click into place7. Lightly tug on the liner to remove the slack Label LinerL o a d i n g F a n - F o l d S u p p l i e s 2-8 Operator’s Handbook8. Close the supply door until the release levers click into place Loading Supplies2-10 Operator’s Handbook Tearing the SuppliesTear Edge M A I N T E N A N C E C A R EC l e a n i n g Use any of the following items to clean the printhead Printhead On-Demand Sensor Turn the platen roller with your finger to clean the entire surface C l e a r i n g L a b e l J a m s 3-6 Operator’s Handbook Solution T R O U B L E S H O O T I N GProblem “Care and Maintenance” for moreDescription C o m m o n E r r o r sError 2710Error DescriptionError DescriptionP r i n t e r S p e c i f i c a t i o n s S P E C I F I C AT I O N SPrinterStorage 14 to 122 F -10 to 50 C Battery and Printer 5% to 90% non-condensingOperating Limits 32 to 109 F 0 to 43 C Relative HumiditySupply Types Labels, tags, or receipt paper S u p p l y S p e c i f i c a t i o n sC a b l e P i n - o u t s Supply Widths 0.5 13 mm minimum 2.99 76 mm maximumA-4 Operator’s Handbook A C C E S S O R I E S C a r r y i n g A c c e s s o r i e s S i n g l e S t a t i o n B a t t e r y C h a r g e rF o u r S t a t i o n B a t t e r y C h a r g e r B-2 Operator’s HandbookL i n e r l e s s P R I N T E R O P T I O N S CB l u e t o o t h C-2 Operator’s Handbook