Manuals / Paxar / Computer Equipment / Printer

Paxar Sierra Sport3 manual C o m m o n E r r o r s, Error, Description, 2710

Models: Sierra Sport3

1 46

Download 46 pages 33.59 Kb

Page 34

C o m m o n E r r o r s

The following is a list of common printer errors you may receive. If you receive a message not listed here, see your System Administrator or call Service at the number listed on the back of this manual.

Error	Description

025	String length is outside the range 0 to
Invalid Length	2710.
101	The format referenced by batch is not
Invalid/Missing	in memory.
409	The printer memory is full. Delete
Memory Full	unnecessary formats or graphics from
	memory.
410	Parity mismatch. Check your parity
Parity	settings at the printer and at the host.
411	Framing error (baud rate mismatch).
Framing	Check your baud rate settings at the
	printer and at the host.
413	Online receive queue is full. Check for
Overrun	a flow control problem.
611	Font, bar code, or density in the batch
Error Loading	does not fit the format.
612	The data in this line of the batch is
Invalid Data	missing or does not match the format.
613	Reference point off supply.
Invalid Data
614	Portion of field off supply or there may
Invalid Data	be an invalid character in the packet.
703	The printer sensed a calibration of
Check Supply	different-sized black marks. Make sure
	the correct supply is loaded.

4-2Operator’s Handbook

Image 34

Paxar Sierra Sport3 manual C o m m o n E r r o r s, Error, Description, 2710

Contents

TC9433OH Rev. AD 12/07 Operator’s HandbookMonarch 9433 Sierra Sport3 Printer All rights reservedCANADIAN D.O.C. WARNING TrademarksTROUBLESHOOTING T A B L E O F C O N T E N T SCARE & MAINTENANCE SPECIFICATIONSACCESSORIES PRINTER OPTIONSU s i n g T h i s M a n u a l G E T T I N G S TA R T E DA u d i e n c e P r i n t e r U t i l i t i e s A d d i t i o n a l D o c u m e n t a t i o nU n p a c k i n g t h e P r i n t e r I n s t a l l i n g t h e B a t t e r y 3 . Close the supply door until the release levers click into place 2 . Insert the connector end of the battery into the printerReady p 1-4 Operator’s Handbook Battery and Safety Information Do not let the battery get wet or come into contact with metal objects C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e s ScrewsConnector Serial Cable1 . Plug the DB9 connector into the DB9 port 2 . Place the cable in the cable cavity3 . Closed the hinged cable door and tighten the screws USB Cable1 . Plug the USB cable into the USB port USB Port USB Cable Cable in Cable CavityDisplay U s i n g t h e D i s p l a y a n d B u t t o n sNavigation ButtonsP r i n t i n g 1-12 Operator’s Handbook The printer may be on or off when loading supplies L O A D I N G S U P P L I E SThis chapter describes how to load supply for non-peel mode prints a continuous strip of supplyL o a d i n g f o r N o n - P e e l M o d e Supply Holder Tabs Exit ChuteTearing the Supplies L o a d i n g f o r P e e l M o d e Peel bar 2-6 Operator’s HandbookPeel roller The liner separates from the label 6. Close the supply door until the release levers click into place7. Lightly tug on the liner to remove the slack Label LinerL o a d i n g F a n - F o l d S u p p l i e s 2-8 Operator’s Handbook8. Close the supply door until the release levers click into place Loading Supplies2-10 Operator’s Handbook Tearing the SuppliesTear Edge M A I N T E N A N C E C A R EC l e a n i n g Use any of the following items to clean the printhead Printhead On-Demand Sensor Turn the platen roller with your finger to clean the entire surface C l e a r i n g L a b e l J a m s 3-6 Operator’s Handbook Solution T R O U B L E S H O O T I N GProblem “Care and Maintenance” for moreDescription C o m m o n E r r o r sError 2710Error DescriptionError DescriptionP r i n t e r S p e c i f i c a t i o n s S P E C I F I C AT I O N SPrinterStorage 14 to 122 F -10 to 50 C Battery and Printer 5% to 90% non-condensingOperating Limits 32 to 109 F 0 to 43 C Relative HumiditySupply Types Labels, tags, or receipt paper S u p p l y S p e c i f i c a t i o n sC a b l e P i n - o u t s Supply Widths 0.5 13 mm minimum 2.99 76 mm maximumA-4 Operator’s Handbook A C C E S S O R I E S C a r r y i n g A c c e s s o r i e s S i n g l e S t a t i o n B a t t e r y C h a r g e rF o u r S t a t i o n B a t t e r y C h a r g e r B-2 Operator’s HandbookL i n e r l e s s P R I N T E R O P T I O N S CB l u e t o o t h C-2 Operator’s Handbook