Manuals / Paxar / Computer Equipment / Printer

Paxar Sierra Sport3 manual L o a d i n g f o r P e e l M o d e

Models: Sierra Sport3

1 46

Download 46 pages 33.59 Kb

Page 21

L o a d i n g f o r P e e l M o d e

L o a d i n g f o r P e e l M o d e

Use these instructions to print labels and separate them from the liner (on-demand).

Release lever

1. Pull the release levers located on both sides of the printer to open the supply door.

2. Remove the tape from a new roll of supply.

3. Push apart the supply holder tabs to widen the supply holders. Insert a roll of supplies.

Supply Holder

Tabs

Loading Supplies 2-5

Image 21

Paxar Sierra Sport3 manual L o a d i n g f o r P e e l M o d e

Contents

Monarch 9433 Sierra Sport3 Printer Operator’s HandbookTC9433OH Rev. AD 12/07 All rights reservedTrademarks CANADIAN D.O.C. WARNINGCARE & MAINTENANCE T A B L E O F C O N T E N T STROUBLESHOOTING SPECIFICATIONSPRINTER OPTIONS ACCESSORIESG E T T I N G S TA R T E D U s i n g T h i s M a n u a lA u d i e n c e A d d i t i o n a l D o c u m e n t a t i o n P r i n t e r U t i l i t i e sU n p a c k i n g t h e P r i n t e r I n s t a l l i n g t h e B a t t e r y 2 . Insert the connector end of the battery into the printer 3 . Close the supply door until the release levers click into placeReady p 1-4 Operator’s Handbook Battery and Safety Information Do not let the battery get wet or come into contact with metal objects Screws C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e s1 . Plug the DB9 connector into the DB9 port Serial CableConnector 2 . Place the cable in the cable cavity1 . Plug the USB cable into the USB port USB Cable3 . Closed the hinged cable door and tighten the screws USB Port USB Cable Cable in Cable CavityNavigation U s i n g t h e D i s p l a y a n d B u t t o n sDisplay ButtonsP r i n t i n g 1-12 Operator’s Handbook This chapter describes how to load supply for L O A D I N G S U P P L I E SThe printer may be on or off when loading supplies non-peel mode prints a continuous strip of supplyL o a d i n g f o r N o n - P e e l M o d e Exit Chute Supply Holder TabsTearing the Supplies L o a d i n g f o r P e e l M o d e 2-6 Operator’s Handbook Peel barPeel roller 7. Lightly tug on the liner to remove the slack 6. Close the supply door until the release levers click into placeThe liner separates from the label Label Liner2-8 Operator’s Handbook L o a d i n g F a n - F o l d S u p p l i e sLoading Supplies 8. Close the supply door until the release levers click into placeTearing the Supplies 2-10 Operator’s HandbookTear Edge C A R E M A I N T E N A N C EC l e a n i n g Use any of the following items to clean the printhead Printhead On-Demand Sensor Turn the platen roller with your finger to clean the entire surface C l e a r i n g L a b e l J a m s 3-6 Operator’s Handbook Problem T R O U B L E S H O O T I N GSolution “Care and Maintenance” for moreError C o m m o n E r r o r sDescription 2710Description ErrorDescription ErrorS P E C I F I C AT I O N S P r i n t e r S p e c i f i c a t i o n sOperating Limits 32 to 109 F 0 to 43 C Battery and Printer 5% to 90% non-condensingPrinterStorage 14 to 122 F -10 to 50 C Relative HumidityC a b l e P i n - o u t s S u p p l y S p e c i f i c a t i o n sSupply Types Labels, tags, or receipt paper Supply Widths 0.5 13 mm minimum 2.99 76 mm maximumA-4 Operator’s Handbook A C C E S S O R I E S F o u r S t a t i o n B a t t e r y C h a r g e r S i n g l e S t a t i o n B a t t e r y C h a r g e rC a r r y i n g A c c e s s o r i e s B-2 Operator’s HandbookP R I N T E R O P T I O N S C L i n e r l e s sB l u e t o o t h C-2 Operator’s Handbook