Manuals / Paxar / Computer Equipment / Printer

Paxar Sierra Sport3 manual Use any of the following items to clean the printhead

Models: Sierra Sport3

1 46

Download 46 pages 33.59 Kb

Page 28

Use any of the following items to clean the printhead:

Use any of the following items to clean the printhead:

♦A soft cloth moistened with isopropyl alcohol.

Caution: Use isopropyl alcohol on the interior areas only, never on the exterior.

♦A Monarch Cleaning Pen (part number 114226).

To clean the printhead, platen roller, and supply sensors:

1. Turn off the printer by pressing and holding P until the display is blank.

Note: Do not use sharp objects to remove adhesive or label particles from the printhead area.

2. Pull the release levers located on both sides of the printer to open the supply door.

Release Levers

3. Lay the printer on its back.

3-2Operator’s Handbook

Image 28

Paxar Sierra Sport3 manual Use any of the following items to clean the printhead

Contents

Operator’s Handbook Monarch 9433 Sierra Sport3 PrinterTC9433OH Rev. AD 12/07 All rights reservedCANADIAN D.O.C. WARNING TrademarksT A B L E O F C O N T E N T S CARE & MAINTENANCETROUBLESHOOTING SPECIFICATIONSACCESSORIES PRINTER OPTIONSU s i n g T h i s M a n u a l G E T T I N G S TA R T E DA u d i e n c e P r i n t e r U t i l i t i e s A d d i t i o n a l D o c u m e n t a t i o nU n p a c k i n g t h e P r i n t e r I n s t a l l i n g t h e B a t t e r y 3 . Close the supply door until the release levers click into place 2 . Insert the connector end of the battery into the printerReady p 1-4 Operator’s Handbook Battery and Safety Information Do not let the battery get wet or come into contact with metal objects C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e s ScrewsSerial Cable 1 . Plug the DB9 connector into the DB9 portConnector 2 . Place the cable in the cable cavityUSB Cable 1 . Plug the USB cable into the USB port3 . Closed the hinged cable door and tighten the screws USB Port USB Cable Cable in Cable CavityU s i n g t h e D i s p l a y a n d B u t t o n s NavigationDisplay ButtonsP r i n t i n g 1-12 Operator’s Handbook L O A D I N G S U P P L I E S This chapter describes how to load supply forThe printer may be on or off when loading supplies non-peel mode prints a continuous strip of supplyL o a d i n g f o r N o n - P e e l M o d e Supply Holder Tabs Exit ChuteTearing the Supplies L o a d i n g f o r P e e l M o d e Peel bar 2-6 Operator’s HandbookPeel roller 6. Close the supply door until the release levers click into place 7. Lightly tug on the liner to remove the slackThe liner separates from the label Label LinerL o a d i n g F a n - F o l d S u p p l i e s 2-8 Operator’s Handbook8. Close the supply door until the release levers click into place Loading Supplies2-10 Operator’s Handbook Tearing the SuppliesTear Edge M A I N T E N A N C E C A R EC l e a n i n g Use any of the following items to clean the printhead Printhead On-Demand Sensor Turn the platen roller with your finger to clean the entire surface C l e a r i n g L a b e l J a m s 3-6 Operator’s Handbook T R O U B L E S H O O T I N G ProblemSolution “Care and Maintenance” for moreC o m m o n E r r o r s ErrorDescription 2710Error DescriptionError DescriptionP r i n t e r S p e c i f i c a t i o n s S P E C I F I C AT I O N SBattery and Printer 5% to 90% non-condensing Operating Limits 32 to 109 F 0 to 43 CPrinterStorage 14 to 122 F -10 to 50 C Relative HumidityS u p p l y S p e c i f i c a t i o n s C a b l e P i n - o u t sSupply Types Labels, tags, or receipt paper Supply Widths 0.5 13 mm minimum 2.99 76 mm maximumA-4 Operator’s Handbook A C C E S S O R I E S S i n g l e S t a t i o n B a t t e r y C h a r g e r F o u r S t a t i o n B a t t e r y C h a r g e rC a r r y i n g A c c e s s o r i e s B-2 Operator’s HandbookL i n e r l e s s P R I N T E R O P T I O N S CB l u e t o o t h C-2 Operator’s Handbook