LIGHTING INSTRUCTIONS - Millivolt Valve
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
A.This appliance is equipped with an ignition device which auto- matically lights the pilot. Do not try to light the pilot by hand.
B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
-Do not try to light any appliance.
-Do not touch any electric switch; do not use any phone in your
building.
-Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions.
-If you cannot reach your gas supplier, call the fire depart- ment.
C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance & to replace any part of the control system & any gas control which has been under water.
LIGHTING INSTRUCTIONS
1.STOP! Read the safety information above on this label.
2.Set wall thermostat to lowest setting, if applicable.
3.Turn off all electric power to the appliance, if applicable.
4.This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.
5.Partially depress and turn gas control
knob clockwise 
past "Pilot" to "Off" position.
Note: Knob cannot be turned from "Pilot" to "Off" unless knob is pushed in slightly. Do not force.
6Allow sufficient length of time (minimum 5 minutes) for any gas in the combustion chamber to escape. If you still smell gas, STOP! Follow "B" in the safety information above on this label. If you don't smell gas, go to the next step.
7. Turn gas control knob back to "Pilot" position.
8.Depress gas control knob fully and hold to ignite pilot. Once the pilot ignites, continue depressing knob for approxi- mately 5 seconds, or until pilot flame indicator is in the RED zone. If pilot does not stay lit, repeat steps 5 through 8, allowing a longer period before releasing gas control dial.
-If gas control knob does not pop up when released, stop and immediately call your service technician or gas sup- plier.
-If the pilot will not stay lit after several tries, turn the gas control knob to "Off" and call your service technician or gas supplier.
9.Turn gas control knob 
to "On" posi- tion.
10.Turn
11.Turn on the burner switch and close control door.
12.Turn on all electric power to the appliance, if applicable.
13.Set thermostat to desired setting, if applicable.
Note: Sufficient time must be allowed for air to escape from lines if the unit is being lit for the first time.
TO TURN OFF GAS TO APPLIANCE
1.Set wall thermostat to lowest setting, if applicable.
2.Turn off all electric power to the appliance if service is to be performed.
3.Push in gas control knob slightly and turn clockwise 
to "Off". Do not force.
FIRST FIRE | OPERATING |
When lit for the fi rst time, the fi replace will emit a slight odour for a couple of hours. This is due to the curing of paints, seal- ants and lubricants used in the manufacturing process. This condition is temporary. Open doors and windows to ventilate area. Smoke and fumes caused by the curing process may cause discomfort to some individuals.
It is normal for fi replaces fabricated of steel to give off some expansion and/or contraction noises during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or cook stove oven.
The Town and Country Fireplace comes equipped with either a manual (millivolt) combination gas valve or an electronic gas valve. An optional wall switch or thermostat (Canada only) may be installed to operate the burner automatically on both types of valve.
Manual Valve: Once a pilot light has been established, and the gas valve knob turned to the "ON" position (Manual Valve) or simply switched on with the "Burner" switch, the unit may be operated in one of two ways; manually adjusting the fl ame and/or turning the unit on and off automatically with a wall thermostat.
36ARB2 23 |
