Philips KX-HCM8 manual

Operating Instructions

Notes

•Make sure the Power Indicator is always in the upper right corner when you mount.

•The upside down mounting may cause Network Camera to fall down.

Power Indicator	On the Stand	On the wall	On the ceiling
Power Indicator
top		top
top		bottom
		bottom
	bottom		top
bottom			bottom
			bottom

CAUTION

Network Camera is intended for indoor use only. Prolonged exposure to direct sunlight or halogen light may damage the CMOS sensor.

90

Image 90

Philips KX-HCM8 operating instructions Power Indicator On the Stand On the wall On the ceiling Top

Contents

Network Camera Introduction For operation assistance Call Trademarks Network Camera Memo Important Safety Instructions Table of Contents Specification and Troubleshooting Technical GuidesIndex 115 Section Main Features Getting to Know Network Camera Update Firmware AuthenticationMulti-Language Display System Requirements Authentication-System Security Feature Authentication window Included Accessories Setup CD-ROM Camera Feature Locations Front View Rear View Bottom View Network Camera Setup Installation Procedure Network Camera Configuration Type Type 2-Internet Connection with a Broadband Router Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PC How to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Network Parameters Table Network Camera Configuration Type Port NoDefault IP address How to refer the network parameters from the PC Enter winipcfg and click OK. IP configuration window appears Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top If Top Page does not appear Operating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Multi-Camera Motion JpegSingle Camera Help ActiveX Controls Single Camera Screen Using Operation Bar Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Primary ViewerClicking Start Capture Secondary Multi-Camera Screen Setup Setup Go to Top AdministratorCamera Setup Name/Time Entered. If any operational issues are changed, try This option first. Refer toFunctions of Network Camera Go to Top Network Instructions for the data fields Enter only the number Dhcp Ddns File size of the image Name Name/TimeCamera Date Auto AdjustmentTime Changed AM/PM or 24H Time Zone Security Administrator Click Security Administrator on Setup Enable For Setup PasswordRetype Click Security General User on Setup Security General User User ID List Delete or ModifyNew User Top View Image Image ResolutionInstructions for the data fields Top 160 x Image Quality Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer window Alarm enable condition Sets the image resolution and image qualityActive Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup Fixed Indoor Power LineWhite Balance Fixed Multi-Camera URL * 1 or Host Enable check boxIP Address or Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Restart Click Restart Now Update Firmware Click Update Firmware Operating Instructions Reset to Factory Default Click Reset to Factory Default on Setup Click Execute Technical Guides Mounting Flexible Stand MountingTripod Mounting Wall Mounting Ceiling Mounting Power Indicator On the Stand On the wall On the ceiling Top Pin Function Interfacing to the External I/OExplanation of External I/O External Sensor Input Circuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character set Displayable character set Maintenance Specification and Troubleshooting Network Camera Reset Procedure-Default Settings Default Settings List Items Factory Default Indispensable setting Value Network Image Transfer 100 For assistance, please call 101 Items Factory Default Indispensable setting Value Camera Specifications Network Camera Specifications DescriptionOther Specification Description SMTP, FTP Troubleshooting About Network Camera SetupProblem Cause and Remedy For Indicator Control window ISP Network window on About Network Camera Setup Problem Cause and Remedy About Top View Image screen View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information 114 Index Operating Instructions TCP/IP For product service When you ship the product