Starting to use
Turning on the power
Please ensure that all preparations have been completed before turning on the power. (Refer to pages 18 – 21.)
)Turn the focus/zoom ring to adjust
the projected image focus and size. | Zoom |
Focus
#Remove the lens cover.
$Connect the accessory power cord.
%Press the MAIN POWER switch to the “” side to turn on the power. The power indicator on the projector will illuminate red.
&Press the POWER button.
The power indicator on the projector will flash green. After a short period, the button will illuminate green, and a picture will be projected.
POWER |
|
|
|
| LIGHT |
| INPUT |
|
VIDEO | CMPN T | PC |
MENU |
|
|
| ENTER |
|
|
| FREEZE |
MODE
ASPECTUSER
VOLUME
MUTE
SD
SD MENU TIME
Turning off the power
#Press the POWER button. “POWER OFF” is
displayed on the screen. |
| POWER | OFF |
| ||
| OK |
| CANCEL |
|
| |
$Select “OK” using the I and H buttons and |
|
|
|
| ||
|
|
|
|
|
| |
press the ENTER button. |
|
|
|
| Operation | |
the cooling fan stops). |
|
|
|
| ||
The lamp unit will switch off and the picture will stop being projected. (The |
| |||||
power indicator on the projector will illuminate orange.) |
|
|
|
|
| |
%Wait until the power indicator on the projector illuminates red (until |
| |||||
Do not in any way cut power to the projector while the cooling fan is still | Basic | |||||
projector, unplug the power cord from the electrical outlet or turn off | ||||||
operating. Be careful not to switch off the MAIN POWER switch of the |
| |||||
switches such as tabletop power switches.
&Press the MAIN POWER switch to the “O” side to turn off the power.
NOTE:
BAfter the power is turned off, the lamp unit will take some time to cool |
down. If you turn the power back on again before the lamp unit has cooled |
down, the lamp unit may not turn on straight away, but it will turn on |
'Press the INPUT select button to select the input signal.
The input signal selected will change as shown at
|
| VIDEO | |
|
|
| VIDEO |
INPUT |
| SD CARD |
|
|
| DVI |
|
|
| PC |
|
| Y･PB･PR |
|
|
| CMPNT |
| |
|
|
| |
| VIDEO |
| Y･PB･PR |
|
|
|
PC
SD
DVI
PC
SD CARD
POWER |
|
|
|
| LIGHT |
| INPUT |
|
VIDEO | CMPN T | PC |
| COMPONENT | KEYSTONE |
|
|
MENU
ENTER
NORMALFREEZE
MODE
ASPECTUSER
VOLUME
MUTE
SD
SD MENU TIME
*“DVI” is only for
automatically after a short period. (During this time, the power indicator on |
the projector will flash orange.) |
BWhen the projector is in standby mode (the power indicator on the |
projector is illuminated red), the projector will still draw a maximum 1.5 W |
of power, even when the cooling fan has stopped. |
BIf the MAIN POWER switch is accidentally turned off while the projector is |
being used, the lamp unit may not turn on straight away after the power is |
turned back on. In such cases, the lamp unit will turn back on |
automatically after a short period. (During this time, the power indicator on |
the projector will flash green.) |
BA tinkling sound may be heard while the power indicator is turned off, but |
this is not a sign of a malfunction. |
(While pressing the adjuster buttons, adjust the forward/back angle of tilt of the projector.
If there is keystone distortion in the projected images, carry out keystone correction as described on page 28.
BYou can also turn off the power by pressing the POWER button twice or |
by holding down it for at least 0.5 seconds. |
