Error displays
Errors may be displayed while using an SD memory card. If an error occurs, check the following table for a description of the error.
Error display | Details |
NO CARD | BThere is no SD memory card inserted. |
|
|
NO DATA | BThe SD memory card does not contain any data that |
| can be played back by the projector. |
|
|
UNFORMAT | BThe inserted card does not match the required |
| specifications, for example the format is different. |
|
|
DATA ERROR | BThe data is not compatible and cannot be played |
| back. |
|
|
READ ERROR | BThe data cannot be read from the card. |
|
|
WRITE ERROR | BThe data could not be saved onto the card. Check if |
| the SD memory card is |
| enough free space available. |
|
|
ERROR | BIf “ERROR” is displayed instead of a thumbnail |
| image, it means that the image cannot be displayed |
| because there is no data or the data is incompatible. |
|
|
? | BIf “?” is displayed instead of a thumbnail image, it |
| means that only the thumbnail data cannot be found. |
|
|
UNEXPECTED | BAn error occurred during an operation. If the problem |
ERROR | cannot be reset by pressing the SD MENU button, |
| turn off the projector’s power while referring to |
| “Turning off the power” on page 23, and then turn the |
| power back on again. |
|
|
NOTE:
BPress the SD MENU button to clear an error display.
BA
Indicators
There are two indicators on the control panel of the projector which give information about the operating condition of the projector. These indicators illuminate or flash to warn you about problems that have occurred inside the projector, so if you notice that one of the indicators is on, turn off the power and check the table below for the cause of the problem.
|
| TEMP indicator |
|
|
| |
|
|
|
|
|
|
|
Indicator | Illuminated (red) |
| Flashing (red) | Flashing (red) |
|
|
display | (Lamp unit on) |
| (Lamp unit on) | (Lamp unit off) |
|
|
|
|
|
|
|
|
|
| The surrounding |
| The temperature | The surrounding |
|
|
| temperature or the |
| inside the projector | temperature or the |
|
|
| temperature inside |
| has become | temperature inside |
|
|
| the projector has |
| dangerously high, or | the projector has |
|
|
| become unusually |
| the temperature has | become dangerously |
|
|
Problem | high. |
| suddenly changed. | high, causing the |
|
|
|
|
|
| lamp unit to be |
|
|
|
|
|
| automatically shut |
|
|
|
|
|
| off. |
|
|
|
|
|
|
|
| |
|
|
|
|
| Operation | |
| BUncover the ventilation holes. |
|
| |||
Possible | BThe ventilation holes may be covered. |
|
|
| ||
BThe ambient temperature in the place of use may be too high. |
|
| ||||
cause | BThe air filter may be blocked. |
|
|
| ||
|
|
|
|
| Advanced | |
Remedy | place where the temperature is between 0 °C (32 °F) and 35 °C |
| ||||
| BSet up the projector in a place where the temperature is |
|
| |||
| between 0 °C (32 °F) and 40 °C (104 °F) and the humidity is |
|
| |||
| between 20% and 80% (with no condensation). [If you set the |
|
| |||
| FAN CONTROL to “HIGH” (page 40), set up the projector in a |
|
| |||
| (95 °F) and the humidity is between 20% and 80% (with no |
|
| |||
|
| |||||
| condensation).] |
|
|
|
|
|
|
|
|
|
|
| |
| BTurn off the MAIN POWER switch by following the procedure |
|
| |||
| on page 23, and then clean the air filter (refer to page 53). |
|
| |||
|
|
|
|
|
| Others |
|
|
|
|
|
| |
|
|
|
|
|
|
|
