Plug in the TV and the VCR | Philips SVA102 specification

Hookups Without a Cable Box/Direct Broadcast System (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on

type (supplied) or screw-on type of coaxial cable, whichever you prefer.)

Antenna or Cable

ANT

IN

					AUDIO
				ANT	OUT IN	OUT
				ANT	VIDEO	CH3 CH4
					VIDEO
				IN		75V
						75V
						ANT	/
AUDIO						CABLE
AUDIO
OUT	IN			OUT			ANTENNA IN Jack
							ANTENNA IN Jack
VIDEO		CH3	CH4				(on back of TV)
VIDEO						RF coaxial cable	example only
							example only

4

Plug in the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. Set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 03.

	CH	4
	or	3
	CH	3
	CH

CH3 / CH4

Switch

CH3 CH4

ANT

IN

ANT

IN

AUDIO

OUT

IN

OUT

VIDEO CH3 CH4

AUDIO
OUT	IN	OUT
VIDEO		CH3 CH4

6

You are ready to turn on the VCR. Please go to page 11 before turning on the VCR.

Image 7

Philips SVA102 owner manual Hookups Without a Cable Box/Direct Broadcast System cont’d, Plug in the TV and the VCR

Contents

Video Cassette Recorder For Customer Use Warranty Verification Safety Precautions FeaturesIntroduction Table of Contents Replace the battery compartment lid Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenance Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast System Plug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’d Connections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Select the channel you want to watch at the Cable Box/DBS Recording One Channel/Watching Another Hookups With a Stereo TV 2Turn on the TV Turning on Your VCR Automatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’d Follow the steps below to set your VCR’s clock. Make sure Setting the Clock 96-7 Setting the Clock cont’d Language Selection Press the Counter RESET/EXIT button Press the Display button once Clock mode OFF mode Press the Display button once Count modeOn-Screen Status Displays Rental Selector Button Remote Control ButtonsPower Button Number Buttons CLOCK/COUNTER Button Counter RESET/EXIT ButtonEject Button Auto Repeat Button VCR Display Panel Front Panel Video OUT Jack AC Power CordRear Panel Audio OUT Jack Read and follow the steps below to play a tape Playing 1Turn on the TV Insert a tape Recording Stopping an OTR Starting an OTR Program Number → Once Daily Weekly Timer Recording Repeat the procedure in to set the recording’s end time Timer Recording cont’d 4Press the Counter RESET/EXIT button to exit Correcting a Timer Recording Cancelling a Timer Recording Press the Play button or the Stop button repeatedly to Auto ReturnSelect Auto Return To stop recording, press the Stop button Press the VCR/TV button on the VCR remote control toTo return to the channel being recorded, use the TV Put the VCR in VCR position. The VCR/TV light will appear RF coaxial cable Rerecording Tape Duplication Repeat Play Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLP Rental Play Press the Play button to watch the tape Real-Time Counter Memory Automatic Playback Features Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel Channel 3 or Glossary Specifications Video Cassette Recorder Limited Warranty Index Supplied Accessories