Philips VCR 462 manual

50 Multi-Channel Television Sound System (VRX462 only) (cont’d)

To receive and record programs broadcast in second audio, follow steps 1 - 10. To record a program broadcast in stereo, make one of the connections shown, then follow steps 1 - 10.

If you have a Stereo and a Monitor TV, use a video cable to connect the VCR’s VIDEO OUT Jack to the TV’s VIDEO IN Jack. Use audio cables to connect the VCR’s AUDIO OUT Jacks to the Stereo’s AUDIO IN Jacks.

CABLE
BOX IN	OUT ANT.IN
	R
AUDIO
	L
CH3 CH4	RF OUT	CABLE
VIDEO
		BOX	IN OUT ANT.IN
			R
		AUDIO
			L
		VIDEO	RF OUT
		VIDEO
	CH3 CH4

OR, if you have a single-speaker TV, connect the VCR to the TV by following the steps on pages six

- nine. (Use an RF coaxial cable to

connect the VCR’s RF OUT Jack

1

Press the VCR button, then press the MENU button.

2

Press the Number 4 button to select INPUT SELECT.

3

Press the Number 1 button so that (ON) appears beside

TUNER.

4

Press the EXIT/STATUS button.

5

Press the MENU button.

6

Press the Number 3 button to select TUNER SET UP.

to the TV’s ANTENNA IN Jack.)

7

Press the Number 6 button to select TV STEREO or the Number 7 button to select SECOND AUDIO. (ON) will appear beside your selection. You can not record a program in both stereo and second audio at the same time.

8

Press the EXIT/STATUS button to exit.

9

Use the CHANNEL Up/Down buttons to select a channel to record.

10

Press the REC(ord)/OTR button to start recording.

Helpful Hints

•If you want to connect the VCR to a Stereo TV, follow these steps.

1)Connect the antenna or cable signal to the VCR’s ANT(enna) IN Jack.

2)Use stereo audio cables to con- nect the VCR’s AUDIO OUT Jacks to the TV’s AUDIO IN Jacks.

3)Use a video cable to connect the VCR’s VIDEO OUT Jack to the TV’s VIDEO IN Jack.

•Make sure the TV and the Stereo (if applicable) are in Line Input or Auxiliary mode. Please refer to your TV or Stereo owner’s manual for details.

Image 50

Philips VCR 462 warranty Multi-Channel Television Sound System VRX462 only cont’d

Contents

Video Cassette Recorder VRX442 VRX462 Dear Philips Magnavox product owner For Customer Use Introduction FeaturesSafety Precautions Table of Contents Using the Remote Control Before Using Your VCRPutting Batteries in the Remote Control VCR Maintenance Hookups Without a Cable Box Disconnect the antenna or cable from your TV Hookups Without a Cable Box cont’d Antenna Or Cable Recording or Viewing a Scrambled or Unscrambled Channel Timer RecordingsHookups With a Cable Box/DSS Receiver Watching TV With the VCR Turned Off Playing a Tape Hookups With a Cable Box/DSS Receiver cont’dRecording One Channel/Watching Another Antenna in Jack On back of TV Turn on the TV Turning on Your VCRVCR will come on and the menu shown below will appear Press the Menu button. The menu shown below will appear Wait for the VCR to program channels On the display panel of the VCR Press the Number 3 button to select Tuner SET UPProgramming Channels Press the Menu button to bring up the main menu display Adding/Deleting ChannelsPress the VCR button Press the Number 4 button to select ADD/DELETE CH Press the Number 3 button to select SET Manual Clock Setting the ClockPress the VCR button, then press the Menu button Press the EXIT/STATUS button Time Zone Selection Press the Number 4 button to select SET Time Zone Setting the Clock cont’d Manual PBS Channel Selection Turn off the VCR Automatic PBS Channel SelectionPress the EXIT/STATUS button. You will be prompted to Channels Daylight-Saving Time Selection Press the EXIT/STATUS button to exit Language Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 3 button to select Language Remote Control Buttons VCR PLUS+/ENTER Button Rame ADVance ButtonStop Button EXIT/STATUS Button Display Panel VRX462 Remote Sensor Display Panel cont’dOTR Light Tape Speed Lights Memory Light Front Panel Rear Panel Setting the Remote Control to Operate a TV Find the code for your TV Repeat step Cable BOX/DSS Receiver Codes Find the code for your Cable Box/DSS Receiver Repeat step Sound Program Press the Number 2 button to select on Screen ModeOn-Screen Status Displays On Screen On and Counter Only modes Remote Locator When you find the remote control, point the remote atTo program the VCR to find its Remote control only Turn on the TV Insert a tape PlayingRead and follow the steps below to play a tape Appear on the display panel VCR records in a preset volumeRecording Stop. Details are on Stopping an OTR One Touch RecordingStarting an OTR Tape Speed button. Details are on pages 36 Instructions carefully Recording One Channel/Watching AnotherPress the RECord/OTR button to start a recording Select a once, daily or weekly recording Timer RecordingPress the Number 1 button to select Program Recording Then turn itself off Instructions continue onFollow the instructions in to set the recording’s stop time Timer Recording cont’d Tape Speeds Checking or Clearing Timer Recordings Local TV Stations Call letters Setting Up the VCR Plus+ Programming SystemTV Channels Cable Channels Examine the lists on 2page Select a ONCE, DAILY, or Weekly recording Monday through Friday Press the EXIT/STATUS button. Program WAS COM Connecting the Controller Cable Box or DSS Receiver Controller Press the Menu button Timer recordingPress the Number 5 button to select SET Cable BOX Press the Menu button or the EXIT/STATUS button Press the Menu button. Wait for a few secondsNumber 2 button to select NO. Use the Number buttons to Cable BOX Control is on will appear for five seconds Press the Number 1 button to set the DSS Receiver Setting the Controller to Operate a DSS ReceiverPress the Number 6 button to select SET DSS Receiver Controller to on Press the Number 1 button to select YES Change the VCR Channels To the Audio in Jack on VCR Rerecording Tape DuplicationVCR 1 will play your tape. Insert a prerecorded tape in VCR Index Search Receiving a Second Audio Program These features are not available with the VRX442Receiving a Stereo Broadcast Multi-Channel Television Sound System VRX462 only cont’d Press the Number 1 button so that on appears beside Hi-Fi Stereo Tape Playback VRX462 only Memory light will appear on the display panel Using the Tape CounterTape Counter Memory Turned ON. Details are on Go-To Feature To remove the Goto display, press the GO-TO button again Play mode Repeat Playback Video Stabilizer Video Stabilizer Viewing a Still Picture Playback OptionsForward and Reverse Searching Viewing a Slow Motion Picture Automatic Operation Features Glossary Cable Box/DSS Receiver Output Channel channel 03 or Specifications Helpful Hints Helpful Hints cont’d Renewed Off mode Ac power cord Hi-fi stereo playback Rewind buttonSafety precautions Automatic With a stereo TV Playback Manually On mode Timer Supplied Accessories