Go-To Feature | Philips VCR 462 specs

Go-To Feature 53

Follow the steps below to program the VCR to go to a place on a tape with a specified tape counter location number.

•Make sure the VCR is in VCR position. (The VCR light will appear on the display panel. If it does not, press the VCR/TV button once.)

1

Press the VCR button.

2

When tape playback is stopped, press the GO-TO button

to bring up the GOTO display.

NOW	1:	00 : 00
GOTO	–:	– – : – –

3

Within 10 seconds, use the Number buttons to enter the desired tape counter location number. For example, to go to tape counter location number 1:20:00, press Number buttons 1, 20, 00.

NOTE: If the desired tape counter location number has a minus (–) before it, enter the minus by pressing the CHANNEL Down button. Press the CHANNEL Up button to remove the minus.

NOW	1: 00 : 00
GOTO	1: 20 : 00

1


CBL/DSS	VCR	TV

EJECT POWER MUTE

	VOL	F.ADV	CHANNEL
		PAUSE/STILL
		PLAY
	REW		FF
4	VCR PLUS+		LIGHT
4	/ENTER	STOP	LIGHT
		STOP
	EXIT/STATUS MENU		CLEAR
	1	2	3	3
	4	5	6	3
	7	8	9	2
	100	0	GO-TO
	REC/OTR	INDEX	MEMORY
		...
		...
		VAR. SLOW	TRACKING SKIP

SPEED VCR/TV SLOW				SEARCH

4

Within 10 seconds, press the PLAY, STOP, POWER, or REC(ord)/OTR button. The VCR will fast forward or rewind the tape to the selected tape counter location. The tape counter will appear on-screen as the VCR rewinds or fast forwards the tape. Then, depending on which button you pressed, the VCR will either begin tape playback, stop the tape, turn itself off, or start recording the current channel.

Button pressed	VCR action
PLAY	Begin tape playback
STOP	Stop the tape
POWER	Turn off VCR
REC(ord)/OTR	Begin recording current channel

REMOTE LOCATOR

Helpful Hints

•To remove the GOTO display, press the GO-TO button again.

•The tape counter location number you enter at step 3 must be valid.

•To stop the tape during rewinding or fast forwarding (before the tape reaches the requested tape counter location number), press the STOP button.

Image 53

Philips VCR 462 warranty Go-To Feature, To remove the Goto display, press the GO-TO button again

Contents

Video Cassette Recorder VRX442 VRX462 For Customer Use Dear Philips Magnavox product owner Introduction FeaturesSafety Precautions Table of Contents Putting Batteries in the Remote Control Before Using Your VCRUsing the Remote Control VCR Maintenance Disconnect the antenna or cable from your TV Hookups Without a Cable Box Antenna Or Cable Hookups Without a Cable Box cont’d Hookups With a Cable Box/DSS Receiver Timer RecordingsRecording or Viewing a Scrambled or Unscrambled Channel Watching TV With the VCR Turned Off Recording One Channel/Watching Another Hookups With a Cable Box/DSS Receiver cont’dPlaying a Tape Antenna in Jack On back of TV Turn on the TV Turning on Your VCRVCR will come on and the menu shown below will appear Wait for the VCR to program channels Press the Menu button. The menu shown below will appear On the display panel of the VCR Press the Number 3 button to select Tuner SET UPProgramming Channels Press the VCR button Adding/Deleting ChannelsPress the Menu button to bring up the main menu display Press the Number 4 button to select ADD/DELETE CH Press the VCR button, then press the Menu button Setting the ClockPress the Number 3 button to select SET Manual Clock Press the EXIT/STATUS button Press the Number 4 button to select SET Time Zone Time Zone Selection Manual PBS Channel Selection Setting the Clock cont’d Press the EXIT/STATUS button. You will be prompted to Automatic PBS Channel SelectionTurn off the VCR Channels Press the EXIT/STATUS button to exit Daylight-Saving Time Selection Language Selection Press the Number 2 button to select VCR SET UPLanguage Press the Number 3 button to select Language Remote Control Buttons Stop Button Rame ADVance ButtonVCR PLUS+/ENTER Button EXIT/STATUS Button VRX462 Display Panel OTR Light Display Panel cont’dRemote Sensor Tape Speed Lights Memory Light Front Panel Rear Panel Find the code for your TV Repeat step Setting the Remote Control to Operate a TV Find the code for your Cable Box/DSS Receiver Repeat step Cable BOX/DSS Receiver Codes On-Screen Status Displays Press the Number 2 button to select on Screen ModeSound Program On Screen On and Counter Only modes Remote Locator When you find the remote control, point the remote atTo program the VCR to find its Remote control only Turn on the TV Insert a tape PlayingRead and follow the steps below to play a tape Recording VCR records in a preset volumeAppear on the display panel Stop. Details are on Starting an OTR One Touch RecordingStopping an OTR Tape Speed button. Details are on pages 36 Instructions carefully Recording One Channel/Watching AnotherPress the RECord/OTR button to start a recording Press the Number 1 button to select Program Timer RecordingSelect a once, daily or weekly recording Recording Then turn itself off Instructions continue onFollow the instructions in to set the recording’s stop time Tape Speeds Timer Recording cont’d Checking or Clearing Timer Recordings Local TV Stations Call letters Setting Up the VCR Plus+ Programming SystemTV Channels Cable Channels 2page Examine the lists on Monday through Friday Select a ONCE, DAILY, or Weekly recording Press the EXIT/STATUS button. Program WAS COM Cable Box or DSS Receiver Controller Connecting the Controller Press the Menu button Timer recordingPress the Number 5 button to select SET Cable BOX Number 2 button to select NO. Use the Number buttons to Press the Menu button. Wait for a few secondsPress the Menu button or the EXIT/STATUS button Cable BOX Control is on will appear for five seconds Press the Number 6 button to select SET DSS Receiver Setting the Controller to Operate a DSS ReceiverPress the Number 1 button to set the DSS Receiver Controller to on Change the VCR Channels Press the Number 1 button to select YES To the Audio in Jack on VCR Rerecording Tape DuplicationVCR 1 will play your tape. Insert a prerecorded tape in VCR Index Search Receiving a Second Audio Program These features are not available with the VRX442Receiving a Stereo Broadcast Press the Number 1 button so that on appears beside Multi-Channel Television Sound System VRX462 only cont’d Hi-Fi Stereo Tape Playback VRX462 only Tape Counter Memory Using the Tape CounterMemory light will appear on the display panel Turned ON. Details are on To remove the Goto display, press the GO-TO button again Go-To Feature Repeat Playback Play mode Video Stabilizer Video Stabilizer Forward and Reverse Searching Playback OptionsViewing a Still Picture Viewing a Slow Motion Picture Automatic Operation Features Cable Box/DSS Receiver Output Channel channel 03 or Glossary Specifications Helpful Hints Helpful Hints cont’d Renewed Safety precautions Automatic With a stereo TV Playback Ac power cord Hi-fi stereo playback Rewind buttonOff mode Manually On mode Timer Supplied Accessories