Problem solving Turbo Timer programming | Philips VR 260/07 specification

O K

6 Insert a cassette without erase protection


	What is erase protection?
	VHS cassettes can be protected from over-recording by
	breaking off a thin strip of plastic (arrow). This erase
	protection can be overridden by sticking one or more
	strips of adhesive tape tightly over the gap which has
	strips of adhesive tape tightly over the gap which has	PARDON?
	been created.	PARDON?

7 SWITCH OFF THE VIDEO RECORDER WITH THE
STANDBY/ON BUTTON m ! IF YOU DON’T
DO THIS, THE SET WILL NOT RECORD.
The display will show “k”

Problem solving (Turbo Timer programming)

PROBLEM

Error message: “CASS”,

“k” and “v” will blink in the display

SOLUTION

A recording was programmed, but there is no cassette in the machine. Insert a cassette ready for recording without erase protection.

Error message: “FULL“

Cassette is ejected during recording

Cassette is ejected after programming

The set cannot be used during recording

Error message: “CLK“

All the available memory locations in your video recorder for timer and VIDEO Plus programming are full. Delete a programmed recording (see chapter “Delete / check / change programmed recordings”).

The end of the tape was reached during a programmed recording.The recording could not be completed satisfactorily.

A cassette with erase protection was inserted. Please deactivate the erase protection or insert another cassette which is ready for recording.

Once started, a recording can only be interrupted by pressing the STANDBY/ON

button m. WARNING: This will not only stop the recording, but it will also delete the programmed recording from the memory of the video recorder.

The time has not been set or not set correctly. A Turbo Timer recording is not possible. Please enter the correct time (Section “Changing the time and date”)

ENGLISH	37	PROBLEM SOLVING

Image 37

Philips VR 260/07 operating instructions Problem solving Turbo Timer programming

Contents

Table of contents With VR 260/07 Remote control Important notes for operation Introduction Most important functions of your new video recorder Important information for customers in Great Britain Preparing the remote control for operation Connecting the video recorderConnecting to a TV set with a scart socket When using this video recorder Confirm with OK Problem There is no test image Connecting additional devicesCheck the cable connections Setting TV channels, date and time for the first time Initial installation What is a channel, or a special channel? What is an on-screen menu?Searching for a TV channel manually Following the corresponding instructions on Screen.PARDON? Allocating decoder What is a decoder?Don’t know the channels for my TV stations Desired TV station Check decoder allocation at a glance Using a satellite receiverTo which TV channel on the video recorder a decoder is This channel Searching for TV channels automatically Settings Sorting and clearing of TV channels manually Additional 0.Therefore for 9 you must enter Changing the time and date General information Operating instructionsNavigation in the main menu Playing cassettes PlaybackPlaying back Ntsc cassettes What types of display are available to me? Selecting tape position display typeDisplay shows the playing time Remaining until the end Cassette 0000 hours / minutes Button G Reset / display tape position Later by pressing a button Bookmark at the appropriate place on the tape Immediately to playback Play compact VHS cassettes Still picture / slow motion Optimizing tracking Removing picture interferenceOptimizing still picture Manual recording Starting recording manually Stopping automatically Selecting the recording speed Lining up manual recordingsStandard Play / Long Play / Auto Long Play Duration of the programmed recording, Is practically no loss of quality during transfer. We Recording automatically from a satellite receiver Activate / deactivate direct recording Is switched offCannot select on or OFF That direct recordings are not possible Making a direct recording Programmed recordings Programming timer with Video Plus+ Explains how to set the desired recording speed Signals on * or offActivate VPS/PDC Even if they are rescheduled. In the input field Problemsolution Problem solving Video Plus-Programming What is a memory location? Programming timer without Video Plus+Store up to six timer programmings Friday or WEEK. for recordings which are Programming Timer Without Video Plus English And/or v are flashing in the display of the video recorder Problem solving Timer programming Turbo Timer-Recording Problem solving Turbo Timer programming Delete / check / change programmed recordings Using the NexTView LinkIt has been manually deleted Adjusting the child lock Adjusting automatic switch-off10Other functions Repeat Play Replaying cassette continuously TV systems Changing the TV systemProcess and show several transmission systems Select Auto What is an OSD? Adjusting the OSD informationOn-screen menu by following the corresponding Instructions on the screen Energy-saving mode Factory setting of the video recorder is VCR Adapting remote controlRecorder. Each button has been allocated a specific Both video recorders is possible once more Remote Control Codes Using the TV remote control Display.PROBLEM These signals are transmitted11Suppressing interference Optimizing the modulator Switching off the modulator Switching the modulator on / offWith a scart cable, you can switch off the modulator When there is interference with the picture or sound 12Before you call an engineer Possible Cause / Solution English English Video recorder / display English