Selecting tape position display type | Philips VR 260/07 guide

MAIN MENU

CLOCK

AUTO INSTALL

MANUAL SEARCH

TV CHANNEL ALLOC.

RECORD SPEED

AUTO STANDBY

TV SYSTEM

SPECIAL SETTINGS

EXITPMENUOK

SPECIAL SETTINGS

OSD	ON
CLOCK DISPLAY	OFF
COUNTER	QT.LEFTP
SAT RECORDING	OFF
REPEAT PLAY	OFF
DIRECT RECORD	OFF

EXITPMENU	OK

Selecting tape position display type

If the OK button is pressed during playback and recording, the current tape position (hours : minutes : seconds) is shown in the display.There are two different types of display available.

1Press the MENU button on the remote control.The on-screen menu appears

2Use =P- or ;P+ to select the option “SPECIAL SETTINGS” and confirm with

OK

3Use =P- or ;P+ to select the option “COUNTER“

What types of display are available to me?

“LINEAR”:	The display shows the number of
	minutes of tape already played
	(00:00:00 - hours / minutes /
	seconds)
“TIME LEFT”:	The display shows the playing time
	remaining until the end of the	PARDON?
	cassette (00:00 - hours / minutes)	PARDON?

4Use P or Q to select the desired type of display and confirm with OK. The screen will show the message “STORED”

8The counter stops running when unrecorded places are found (“Linear” display type)

4 This is normal, and is necessary for technical reasons.

8The display shows a negative playing time

4This may happen, for example, when you insert an incompletely-rewound cassette into the video recorder and rewind it to the start of the tape. Since the display is automatically reset to “00:00:00” when you insert a cassette, the actual start of the cassette for the set is less than zero - thus in the negative range.The tape position is displayed with a minus sign “-”.

8After inserting a cassette the video recorder shows no remaining playing time

4The set needs a little time to calculate the remaining

playing time. After a few seconds, the display should	PROBLEM
change from --:-- to the corresponding value

ENGLISH	19	SELECTING TAPE POSITION DISPLAY TYPE

Image 19

Philips VR 260/07 operating instructions Selecting tape position display type, What types of display are available to me?

Contents

Table of contents With VR 260/07 Remote control Important notes for operation Introduction Most important functions of your new video recorder Important information for customers in Great Britain When using this video recorder Connecting the video recorderPreparing the remote control for operation Connecting to a TV set with a scart socket Confirm with OK Problem There is no test image Connecting additional devicesCheck the cable connections Setting TV channels, date and time for the first time Initial installation Following the corresponding instructions on Screen.PARDON? What is an on-screen menu?What is a channel, or a special channel? Searching for a TV channel manually Desired TV station What is a decoder?Allocating decoder Don’t know the channels for my TV stations This channel Using a satellite receiverCheck decoder allocation at a glance To which TV channel on the video recorder a decoder is Searching for TV channels automatically Settings Sorting and clearing of TV channels manually Additional 0.Therefore for 9 you must enter Changing the time and date General information Operating instructionsNavigation in the main menu Playing cassettes PlaybackPlaying back Ntsc cassettes Cassette 0000 hours / minutes Selecting tape position display typeWhat types of display are available to me? Display shows the playing time Remaining until the end Button G Reset / display tape position Later by pressing a button Bookmark at the appropriate place on the tape Immediately to playback Play compact VHS cassettes Still picture / slow motion Optimizing tracking Removing picture interferenceOptimizing still picture Manual recording Starting recording manually Stopping automatically Duration of the programmed recording, Lining up manual recordingsSelecting the recording speed Standard Play / Long Play / Auto Long Play Is practically no loss of quality during transfer. We Recording automatically from a satellite receiver That direct recordings are not possible Is switched offActivate / deactivate direct recording Cannot select on or OFF Making a direct recording Programmed recordings Programming timer with Video Plus+ Even if they are rescheduled. In the input field Signals on * or offExplains how to set the desired recording speed Activate VPS/PDC Problemsolution Problem solving Video Plus-Programming Friday or WEEK. for recordings which are Programming timer without Video Plus+What is a memory location? Store up to six timer programmings Programming Timer Without Video Plus English And/or v are flashing in the display of the video recorder Problem solving Timer programming Turbo Timer-Recording Problem solving Turbo Timer programming Delete / check / change programmed recordings Using the NexTView LinkIt has been manually deleted Adjusting the child lock Adjusting automatic switch-off10Other functions Repeat Play Replaying cassette continuously Select Auto Changing the TV systemTV systems Process and show several transmission systems Instructions on the screen Adjusting the OSD informationWhat is an OSD? On-screen menu by following the corresponding Energy-saving mode Both video recorders is possible once more Adapting remote controlFactory setting of the video recorder is VCR Recorder. Each button has been allocated a specific Remote Control Codes Using the TV remote control Optimizing the modulator These signals are transmittedDisplay.PROBLEM 11Suppressing interference When there is interference with the picture or sound Switching the modulator on / offSwitching off the modulator With a scart cable, you can switch off the modulator 12Before you call an engineer Possible Cause / Solution English English Video recorder / display English