Others
Description of problem | Message display | Possible cause | Recommended action |
|
|
|
|
Hyper magazine cannot be ejected | Host must return | There are some discs that from | Return to user mode, issue REZERO |
in Hyper submode. | all hyper’s disc | the hyper magazine remaining in | command from the host computer |
|
| drives. | requesting that all discs be returned, |
|
|
| and try to perform the operation again |
|
|
| after all discs have been returned. |
|
|
|
|
There exists a drive or drives which |
| ¶ SCSI cable has not been | ¶ Make sure that the SCSI cables have |
fail to be recognized by the host |
| connected properly. | been connected properly. |
computer even though they have |
| ¶ SCSI ID or termination | ¶ Check to see if there is any device on |
been recognized in Config submode. |
| settings have not been | the same bus with the same SCSI ID |
|
| correctly specified. | and to see that the SCSI chain has |
|
|
| been properly terminated. |
|
| ¶ The total length of the SCSI | ¶ |
|
| cables is too long. | the total length of all the cables does |
|
|
| not exceed the maximum allowable |
|
|
| length. |
|
| ¶ Operator has forgotten to | ¶ Reboot the host computer. |
|
| reboot the host computer. |
|
|
|
|
|
There exists a drive which fails to be | scsiID=7 TermOFF | ¶ The power cable for the drive | ¶ Open the rear access door and check |
recognized by the host computer, | in question has not been | to see if the power cable has been | |
and the SCSI ID of the drive is set to |
| connected. | properly connected. |
‘7’ when checked in Config |
| ¶ Drives have been inserted in | ¶ The power supplied by the power |
submode. |
| rear bays #9 through #16 | supply included as standard |
|
| without additional power | equipment is sufficient only for |
|
| supply unit. | operating drives in bays #1 through |
|
|
| #8. Reinstall the drive in one of these |
|
|
| bays or install the additional power |
|
|
| supply unit. |
|
|
|
|
Unable to properly read a disc which |
| ¶ The disc has been inserted | ¶ Check to see if the disc has been |
has been inserted in a drive. |
| upside down. | inserted upside down. |
|
| ¶ The disc is soiled or | ¶ Check to see if the disc is soiled or |
|
| scratched. | scratched, and wipe away any soil or |
|
|
| replace the disc. |
|
|
|
|
An error code is displayed on the | E88, E89,E99, etc. | A mechanical error has occurred | In system administrator mode, open the |
LCD message window and the |
| which has made the changer | access door and take whatever action is |
backlight flashes and the buzzer is |
| unable to continue in operation. | required in order to eliminate the error |
sounded. |
|
| condition. |
|
|
|
|
The LCD message window does not |
| The changer SCSI termination | ¶ When installing is not finished, turn |
come on when the power is turned |
| switch is set to OFF or the SCSI | the SCSI termination switch to ON |
on. |
| cable is not properly connected. | and turn the power OFF and ON. |
Pressing the operation keys has no |
|
| ¶ If the SCSI cable is not properly |
effect. |
|
| connected, turn off the power. And |
|
|
| after connection the cable properly, |
|
|
| turn on the power again. |
|
|
|
|
Buzzer sounds when magazine is | ¶ Memory Failure | Magazine's memory data is not | ¶ Remove and reinsert magazine. |
loaded. | ¶ Error | being read correctly. | ¶ If the magazine data still can't be read |
|
|
| properly, perform a "PROBE" of the |
|
|
| magazine, ten open and close the |
|
|
| door. |
|
|
|
|
English
45
<DRC1184> En
